mcarterbrown.com - View Single Post

Sneaky Sir · 06-18-2010, 08:33 AM

Well guys, I have given up on my 07' Borg Project. Bought an AKA Viking recently and love the thing, and just don't want this project sitting around anymore. Also probably have an X-mag on the way soon, so I gotta fund that as well.

Almost all of the parts listed below are brand new and purchased from Macdev (unless otherwise noted) and have never had air ran through them. The electronic stuff has been plugged into the board just to test them, but again no air has rain through them. Some of them have been put onto the marker and then taken off afterwards.

So I'll just right into it.

Shippping is not included.

Am open to offers and trades, mainly mag parts.

First up is a brand new Tadao Yakuza board. Includes the grip panels, On/Off switch, the RF cord, and also a set of eyes. Turns on just fine, and runs all of the electronic parts as well.

Price: $185

Brand New Dust Black LPR Assembly- Sold

Brand New 07' V2 Solnoid (No air ran through it, clicks when attached to board though)- Price: $85

07' Bolt w/ Bolt Pin (Bolt is brand new. Bolt pin has been filed slightly on the bottom part where it sits in the ram so it would seat properly with the ram)- Price: $40

Brand New Gloss Black 06' Eye Covers- Price: $15

Used Red Valve System (Includes two cupseals and valve spring)

Valve Set Screw Sold

Price: $30

Brand New Gloss Black 07' Eye Covers- Price: $15

Brand New Violent Series Trigger (includes two trigger magnets)
Spring Guide, Trigger Pin, and Spring all sold

Price: $40

Set of lower components. Includes brand new hammer guide, brand new ram, and ram housing. The ram housing has been modified. I couldn't get my bolt to travel far enough back when I pulled it by hand, so I started to bore out the inside of the ram housing hoping to get some more rear travel out of it. It does look like a hackjob though sadly (that's what I get for being in a rush). Might need to be replaced, just throwing it into this set since I don't need it.

Hammer Guide Pin and Ram Cap Sold

Price: 40

Thats all of them for now, more in the future when some of this sells. Now I know my prices seem a little high, these listed are under what I paid for them brand new from Macdev and I'm trying to not take too big a loss on this stuff as its almost all brand new.

Now with that said, if you don't like the price make an offer on this stuff I want to move it out.

Also once again, I will look at trades. Mainly interested in AKA and mag parts. Maybe a Rotor too.

06-18-2010, 08:33 AM	#1 (permalink)
Sneaky Sir MCB Member Join Date: Jul 2008 Location: Hutchinson, MN	Cyborg Parts FS Well guys, I have given up on my 07' Borg Project. Bought an AKA Viking recently and love the thing, and just don't want this project sitting around anymore. Also probably have an X-mag on the way soon, so I gotta fund that as well. Almost all of the parts listed below are brand new and purchased from Macdev (unless otherwise noted) and have never had air ran through them. The electronic stuff has been plugged into the board just to test them, but again no air has rain through them. Some of them have been put onto the marker and then taken off afterwards. So I'll just right into it. Shippping is not included. Am open to offers and trades, mainly mag parts. First up is a brand new Tadao Yakuza board. Includes the grip panels, On/Off switch, the RF cord, and also a set of eyes. Turns on just fine, and runs all of the electronic parts as well. Price: $185 Brand New Dust Black LPR Assembly- Sold Brand New 07' V2 Solnoid (No air ran through it, clicks when attached to board though)- Price: $85 07' Bolt w/ Bolt Pin (Bolt is brand new. Bolt pin has been filed slightly on the bottom part where it sits in the ram so it would seat properly with the ram)- Price: $40 Brand New Gloss Black 06' Eye Covers- Price: $15 Used Red Valve System (Includes two cupseals and valve spring) Valve Set Screw Sold Price: $30 Brand New Gloss Black 07' Eye Covers- Price: $15 Brand New Violent Series Trigger (includes two trigger magnets) Spring Guide, Trigger Pin, and Spring all sold Price: $40 Set of lower components. Includes brand new hammer guide, brand new ram, and ram housing. The ram housing has been modified. I couldn't get my bolt to travel far enough back when I pulled it by hand, so I started to bore out the inside of the ram housing hoping to get some more rear travel out of it. It does look like a hackjob though sadly (that's what I get for being in a rush). Might need to be replaced, just throwing it into this set since I don't need it. Hammer Guide Pin and Ram Cap Sold Price: 40 Thats all of them for now, more in the future when some of this sells. Now I know my prices seem a little high, these listed are under what I paid for them brand new from Macdev and I'm trying to not take too big a loss on this stuff as its almost all brand new. Now with that said, if you don't like the price make an offer on this stuff I want to move it out. Also once again, I will look at trades. Mainly interested in AKA and mag parts. Maybe a Rotor too. __________________ 10mm Auto- From Mild To Extra Wild Last edited by Sneaky Sir; 07-01-2010 at 03:10 AM.