mcarterbrown.com  

Reply
 
Thread Tools Search this Thread
Old 05-07-2012, 06:42 PM   #1 (permalink)
old gun enthusiast
 
Join Date: Apr 2012
Location: Houston

RT classic leaks and I have tried everything

I have an RT classic with level 10 bolt. I have replaced all the o-rings on the gun and flipped my plastic piece in my regulator piston which fixed the majority of the leaks.

However there is still a constant slow leak until the trigger is slightly pulled. It is coming from inside the gun but I can't really tell from where. It isn't coming out of the velocity adjuster but from under the body.

If I lift up on the barrel or push in on the rt valve it leaks a little more.

I have a suspicion it is something to do with the sear but I am unsure.

Any help would be appreciated.
slawre89 is offline   Reply With Quote
Old 05-07-2012, 07:07 PM   #2 (permalink)
Formerly known as T18CAPT
 
Darring D's Avatar
 
Join Date: Nov 2007
Location: Stewartstown, PA

Does it stop when you pull the trigger all the way? with the leaking stick something down the barrel end and push on the bolt. if the leak changes when you move the bolt then it is a level X o-ring carrier. try the next smaller size. Banjo bolt and its o-rings can also cause leaks. try tightening/loosen the banjo bolt while it is leaking and see if anything changes. There was a known issue with the banjo bolt and rail. a newer edition of each were made by AGD. Tuna at Tunamart sells both the upgraded banjo bolt and rail.
__________________
"It is what it is!"

FEEDBACK

Last edited by Darring D; 05-07-2012 at 07:10 PM.
Darring D is offline   Reply With Quote
Old 05-07-2012, 07:40 PM   #3 (permalink)
old gun enthusiast
 
Join Date: Apr 2012
Location: Houston

Holy sh!t!

I think you fixed my problem. I aired up my gun and it was leaking as usual. I then unscrewed the banjo bolt a quarter turn with an allen key and the leak stopped! THANK YOU
slawre89 is offline   Reply With Quote
Old 05-07-2012, 07:42 PM   #4 (permalink)
MCB Member
 
Spider!'s Avatar
 
Join Date: Dec 2008
Location: Houston, TX

If it comes back then...Take any shims out of the level 10. Make sure you use AGD urethane o-rings on the banjo. The o-rings help keep the valve in the right spot.
__________________
My Feedback
Spider! is online now   Reply With Quote
Old 05-07-2012, 08:12 PM   #5 (permalink)
Formerly known as T18CAPT
 
Darring D's Avatar
 
Join Date: Nov 2007
Location: Stewartstown, PA

Glad to help. I hope that is all it was. I had a heck of a time with my Classic RT and had to go the new rail & banjo bolt route.
__________________
"It is what it is!"

FEEDBACK
Darring D is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » Air Gun Designs

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 01:52 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC