mcarterbrown.com
 

Reply
 
Thread Tools Search this Thread
Old 08-28-2007, 04:17 PM   #1 (permalink)
Post Whore
 
LK-13's Avatar
 
Join Date: Jan 2007
Location: St.Catharines Ontario Canada

Mag Measurements

anyone know the OD of a ULE Warp Body and the OD of the warp feed neck?
LK-13 is offline   Reply With Quote
Old 08-28-2007, 06:10 PM   #2 (permalink)
Marathoner
 
secretweaponevan's Avatar
 
Join Date: Aug 2007
Location: Pocono Lake, PA

My CF ULE is 1.125". Just .005" wider than my X-valve.

Probably very close to the same measurement of all (minus Sluggo) bodies and valves.
secretweaponevan is offline   Reply With Quote
Old 08-28-2007, 07:27 PM   #3 (permalink)
Post Whore
 
LK-13's Avatar
 
Join Date: Jan 2007
Location: St.Catharines Ontario Canada

minus Sluggo?
LK-13 is offline   Reply With Quote
Old 08-28-2007, 09:07 PM   #4 (permalink)
Marathoner
 
secretweaponevan's Avatar
 
Join Date: Aug 2007
Location: Pocono Lake, PA

Sluggo Bodies are raw and have a lot of meat on them so that you can get custom work done to them. I believe it is what Deadly Wind uses to make the Karta bodies.

The Sluggo body is the lower right body (without the feedneck, unanodized) in the "Mainbodies" picture at the top of this page:
http://store.airgun.com/index.cfm?fu...&categoryID=10
secretweaponevan is offline   Reply With Quote
Old 08-28-2007, 10:05 PM   #5 (permalink)
Post Whore
 
LK-13's Avatar
 
Join Date: Jan 2007
Location: St.Catharines Ontario Canada

OK so we have one measurement,
anyone out there have a Warp ULE they can check the Feed Tube Diameter of?
I'm hoping it's 0.875" or 7/8".


LK-13 is offline   Reply With Quote
Old 08-28-2007, 10:15 PM   #6 (permalink)
Active Member
 
Havocx's Avatar
 
Join Date: Oct 2006
Location: Ontario Canada
Send a message via Skype™ to Havocx

O.D. = .875 on a ule left like pictured
__________________

Quote:
Originally Posted by Walking_Target View Post
all i could think was that the kid needs to have the agg b*tch slapped off him.
havocxs-feedback
Havocx is offline   Reply With Quote
Old 08-28-2007, 10:20 PM   #7 (permalink)
Post Whore
 
LK-13's Avatar
 
Join Date: Jan 2007
Location: St.Catharines Ontario Canada

WOOHOO!! then the QLOADER set-up i have planned will work no problem!!
LK-13 is offline   Reply With Quote
Old 09-03-2007, 01:32 PM   #8 (permalink)
Post Whore
 
LK-13's Avatar
 
Join Date: Jan 2007
Location: St.Catharines Ontario Canada

anyone know how thick (gage #?) the steel is that the AutoMag sear is made from?
LK-13 is offline   Reply With Quote
Old 09-03-2007, 03:40 PM   #9 (permalink)
Marathoner
 
secretweaponevan's Avatar
 
Join Date: Aug 2007
Location: Pocono Lake, PA

Just calipered mine for you.

.106", so by this chart: Steel Gauge Chart

it would probably be 12 gauge steel.
secretweaponevan is offline   Reply With Quote
Old 09-03-2007, 05:14 PM   #10 (permalink)
Post Whore
 
LK-13's Avatar
 
Join Date: Jan 2007
Location: St.Catharines Ontario Canada

Quote:
Originally Posted by secretweaponevan View Post
Just calipered mine for you.

.106", so by this chart: Steel Gauge Chart

it would probably be 12 gauge steel.
great stuff, thanks.
LK-13 is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » Air Gun Designs

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 07:40 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC