Eye Question

dqsantos · 01-24-2012, 10:17 PM

I have a Viking eye question. I have an 03 Viking with WAS Equalizer board with eyes.

How do I know if they eyes are working? On my Angel you can see the light from the eyes but can't on the Viking. I assume that means they are not working.

If that is true where can I get replacements?

Thanks
David

brock_averill · 01-25-2012, 02:31 PM

Most eyes do not emit light. Turn the gun on with the bolt pulled back. Pull the trigger, if the noid clicks then your eyes have a problem. If you pull it and there is no click then they should be working fine. If you hold the trigger down you can force a shot/click even if the eyes are working and nothing is in the breech. If you end up needing new eyes try either destructivecustoms.com or akalmp.com

Enfamous13 · 01-26-2012, 03:00 PM

Look at the led in back, it blinks slow green when it does not detect a ball, fast green means ball in breach.

dqsantos · 02-02-2012, 09:45 PM

I installed new eyes from AKA and they don't seem to work. The led blinks green (not sure if it is fast or slow). But I cannot fire with or without a ball in the breach until I disable the eyes. Any suggestions?

Thanks
David

brock_averill · 02-02-2012, 09:54 PM

check your eye settings and make sure you have a new battery.

dqsantos · 02-02-2012, 10:56 PM

New battery, set on forced mode; but still not recognizing a ball in the breach. Any other thoughts? I popped the whole thing open to make sure the leads were connected right and they seem to be.

brock_averill · 02-03-2012, 06:35 AM

do you have the eyes in the proper sockets?

dqsantos · 02-03-2012, 11:04 AM

Quote:

Originally Posted by brock_averill

do you have the eyes in the proper sockets?

I believe so based on the diagram in the manual. I could switch them around and see if they work then.

dqsantos · 02-03-2012, 03:10 PM

No luck. Could it be the board? This might be the excuse I need to get a new board

Enfamous13 · 02-03-2012, 04:17 PM

Have you tried taking the eyes out of the body and aiming them at each other? If you get some kind of feedback from the led in back then you may need to clean out the eye sockets and make sure the eyes are aligned correctly.

01-24-2012, 10:17 PM	#1 (permalink)
dqsantos Rec Poster Join Date: Feb 2010	Eye Question I have a Viking eye question. I have an 03 Viking with WAS Equalizer board with eyes. How do I know if they eyes are working? On my Angel you can see the light from the eyes but can't on the Viking. I assume that means they are not working. If that is true where can I get replacements? Thanks David

01-25-2012, 02:31 PM	#2 (permalink)
brock_averill Active Member Join Date: Dec 2009	Most eyes do not emit light. Turn the gun on with the bolt pulled back. Pull the trigger, if the noid clicks then your eyes have a problem. If you pull it and there is no click then they should be working fine. If you hold the trigger down you can force a shot/click even if the eyes are working and nothing is in the breech. If you end up needing new eyes try either destructivecustoms.com or akalmp.com __________________ 04 Immortal Viking Feedback

01-26-2012, 03:00 PM	#3 (permalink)
Enfamous13 Rabid Squirrels Join Date: Jul 2009 Location: Greenville, SC	Look at the led in back, it blinks slow green when it does not detect a ball, fast green means ball in breach. __________________ Feedback PB Nation Mcarter Brown Custom Cockers Automags.org

02-02-2012, 09:54 PM	#5 (permalink)
brock_averill Active Member Join Date: Dec 2009	check your eye settings and make sure you have a new battery. __________________ 04 Immortal Viking Feedback

02-03-2012, 06:35 AM	#7 (permalink)
brock_averill Active Member Join Date: Dec 2009	do you have the eyes in the proper sockets? __________________ 04 Immortal Viking Feedback

02-02-2012, 09:45 PM	#4 (permalink)
dqsantos Rec Poster Join Date: Feb 2010	I installed new eyes from AKA and they don't seem to work. The led blinks green (not sure if it is fast or slow). But I cannot fire with or without a ball in the breach until I disable the eyes. Any suggestions? Thanks David

02-02-2012, 10:56 PM	#6 (permalink)
dqsantos Rec Poster Join Date: Feb 2010	New battery, set on forced mode; but still not recognizing a ball in the breach. Any other thoughts? I popped the whole thing open to make sure the leads were connected right and they seem to be.

02-03-2012, 03:10 PM	#9 (permalink)
dqsantos Rec Poster Join Date: Feb 2010	No luck. Could it be the board? This might be the excuse I need to get a new board

02-03-2012, 04:17 PM	#10 (permalink)
Enfamous13 Rabid Squirrels Join Date: Jul 2009 Location: Greenville, SC	Have you tried taking the eyes out of the body and aiming them at each other? If you get some kind of feedback from the led in back then you may need to clean out the eye sockets and make sure the eyes are aligned correctly. __________________ Feedback PB Nation Mcarter Brown Custom Cockers Automags.org

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search