mcarterbrown.com  

Reply
 
Thread Tools Search this Thread
Old 03-14-2008, 04:38 PM   #11 (permalink)
Post Whore
 
himurax13's Avatar
 
Join Date: Jul 2006
Location: Presently an inmate of Kommifornia.

Quote:
Originally Posted by custar View Post
What size are you using?

custar
Whatever the stock size is. The stock o-rings tend to do that on AKA markers because the tolerences are really tight. Once you finish the rebuild, I would never take the marker down like that again unless you have a problem.
__________________
POG # 877
Quote:
Originally Posted by Heebs View Post
You have serious problems Himura. I remember when I first started buying guns I would oogle your collection.
Quote:
Originally Posted by Mayvik View Post
I'm sad to say I've rejected some pretty choice poon before. Sometimes little Mayvik (brain) gets the better of big Mayvik (peen). I blame it on the a..aha ha ah...ah ah alcohol.
My MCB Feedback
http://www.mcarterbrown.com/forums/f...tml#post331126
himurax13 is offline   Reply With Quote
Old 03-17-2008, 01:51 AM   #12 (permalink)
Post Whore
 
Join Date: Apr 2006

I use 014 o-rings on the LPR. I spent two hours and several 015 o-rings (standard tank o-rings) one night trying to work the blasted things in. I tried every trick in the book with no success. The next day, I bought some 014's (90 durometer), and they went in the first try. Also, I found a flat-bladed screw driver works much better than an allen wrench in working in the o-rings.

custar
custar is offline   Reply With Quote
Old 03-17-2008, 12:20 PM   #13 (permalink)
Post Whore
 
himurax13's Avatar
 
Join Date: Jul 2006
Location: Presently an inmate of Kommifornia.

Well I remembered that the standard tank o-rings are a no-no for use on the LPR and the Ram cartridge because they have a higher durometer rating. I believe the correct o-rings have a durometer of about 90, so I think you are all good.
__________________
POG # 877
Quote:
Originally Posted by Heebs View Post
You have serious problems Himura. I remember when I first started buying guns I would oogle your collection.
Quote:
Originally Posted by Mayvik View Post
I'm sad to say I've rejected some pretty choice poon before. Sometimes little Mayvik (brain) gets the better of big Mayvik (peen). I blame it on the a..aha ha ah...ah ah alcohol.
My MCB Feedback
http://www.mcarterbrown.com/forums/f...tml#post331126
himurax13 is offline   Reply With Quote
Old 03-18-2008, 02:51 PM   #14 (permalink)
Active Member
 
olinar's Avatar
 
Join Date: Feb 2007

I didnt get a parts kit yet but Ive got some orings in the Lpr that seemed to be teh right size, Ive yet to check.

I tore the entire marker down and the Lpr seemed to have the only bad orings. Im going to put it back together and see what I come up with. Im pretty sure the orings I found are tank orings, They are the black ones.
olinar is offline   Reply With Quote
Old 03-18-2008, 10:31 PM   #15 (permalink)
Active Member
 
olinar's Avatar
 
Join Date: Feb 2007

Still leaked with these orings, I saw the thread where a member listed all teh orings needed in AKA markers and their size and all that.
I searched for online sellers that sell orings and they were a bit pricey at a buck a piece.

Any suggestions?
olinar is offline   Reply With Quote
Old 03-18-2008, 10:39 PM   #16 (permalink)
Newbie
 
Join Date: Jul 2006

OTe Web Store

They have it listed for 19.95 shipped for a complete parts kit.
NeoDriftOut is offline   Reply With Quote
Old 03-18-2008, 11:17 PM   #17 (permalink)
Shop Smart,Shop S-Mart
 
doc Zox's Avatar
 
Join Date: Jul 2006

Nitros How to disassemble and clean a viking - PbNation

AKA HOW TO: Viking Hammer Cartridge Disassembly - PbNation

O-rings used in AKA guns and SCM's - PbNation

Product Quantity Size Type Durometer
2 Liter 3 015 Urethane 70
2 Liter 2 009 Urethane 70
2 Liter 1 010 Urethane 90
2 Liter 1 019 Buna 70
2 Liter 1 017 Buna 70
Sidewinder 1 015 Urethane 70
Sidewinder 4 017 Buna 70
Sidewinder 1 113 Urethane 70
Sidewinder 1 008 Urethane 70
Sidewinder 2 010 Urethane 70
2004 Excalibur Ram 2 010 Quad Buna 70
2004 Excalibur Ram 5 015 Urethane 70
2004 Excalibur Ram 1 010 Urethane 70
2004 Excalibur Hammer 2 010 Quad Buna 70
2004 Excalibur Hammer 1 010 Urethane 70
2004 Excalibur Hammer 4 015 Urethane 70
2004 Viking Hammer 2 010 Quad Buna 70
2004 Viking Hammer 1 010 Urethane 70
2004 Viking Hammer 4 015 Urethane 70
Viking/Excalibur SCM-1 3 015 Buna 70
Viking/Excalibur SCM-1 1 014 Buna 70
Viking/Excalibur SCM-1 1 008 Urethane 70
Viking/Excalibur SCM-1 1 003 Buna 70
Viking/Excalibur SCM-1 2 015 Urethane 70
Merlin SCM-1 2 015 Buna 70
Merlin SCM-1 1 014 Buna 70
Merlin SCM-1 1 008 Urethane 70
Merlin SCM-1 1 003 Buna 70
Merlin SCM-1 1 013 Buna 70
Merlin SCM-2 1 015 Buna 70
Merlin SCM-2 1 014 Buna 70
Merlin SCM-2 1 008 Urethane 70
Merlin SCM-2 1 003 Buna 70
Merlin SCM-2 1 013 Buna 70
Matrix SCM-1 4 015 Buna 70
Matrix SCM-1 1 014 Buna 70
Matrix SCM-1 1 008 Urethane 70
Matrix SCM-1 1 003 Buna 70
Matrix SCM-1 1 009 Buna 70
Matrix SCM-2 3 015 Buna 70
Matrix SCM-2 1 014 Buna 70
Matrix SCM-2 1 008 Urethane 70
Matrix SCM-2 1 003 Buna 70
Matrix SCM-2 1 009 Buna 70
Timmy SCM-2 1 015 Buna 70
Timmy SCM-2 1 014 Buna 70
Timmy SCM-2 1 008 Urethane 70
Timmy SCM-2 1 003 Buna 70
Timmy SCM-2 1 020 Buna 70
Timmy SCM-2 1 115 Buna 70
Bushmaster SCM-2 1 015 Buna 70
Bushmaster SCM-2 1 014 Buna 70
Bushmaster SCM-2 1 008 Urethane 70
Bushmaster SCM-2 1 003 Buna 70
Bushmaster SCM-2 1 019 Buna 70
Bushmaster SCM-2 1 016 Buna 70
2003 Viking Hammer 5 015 Urethane 70
2003 Viking Hammer 1 013 Buna 70
2003 Viking Hammer 2 010 Buna 70
2003 Excalibur Ram 6 015 Urethane 70
2003 Excalibur Ram 2 010 Buna 70
2003 Excalibur Ram 1 013 Buna 70
2003 Excalibur Hammer 5 015 Urethane 70
2003 Excalibur Hammer 1 013 Buna 70
2003 Excalibur Hammer 2 010 Buna 70
Old LPR 3 015 Urethane 70
Old LPR 2 013 Buna 70
Old LPR 2 010 Buna 70
Old LPR 1 008 Buna 70
New LPR 3 015 Urethane 70
New LPR 1 013 Buna 70
New LPR 1 010 Buna 70
New LPR 1 008 Buna 70
New LPR 1 014 Buna 70
New Excalibur Bolt 2 015 Buna 70
Old Excalibur Bolt 2 015 Buna 70
Old Excalibur Bolt 1 013 Buna 70
Spring Holders 1 015 Buna 70
Excalibur Ram Plug Cap 1 015 Buna 70
Excalibur, Mac Solenoids 6 3.3x1 Buna 70
Viking, Mac Solenoids 3 3.3x1 Buna 70
Excalibur, Humphrey Solenoids with Adapter Manifold 6 3.3x1 Buna 70
Excalibur, Humphrey Solenoids with Adapter Manifold 2 3.5x1 Buna 70
Excalibur, Humphrey Solenoids with Adapter Manifold 2 4.7x1 Buna 70
Excalibur, Humphrey Solenoids with Adapter Manifold 2 6x1 Buna 70
Viking, Humphrey Solenoids with Adapter Manifold 3 3.3x1 Buna 70
Viking, Humphrey Solenoids with Adapter Manifold 1 3.5x1 Buna 70
Viking, Humphrey Solenoids with Adapter Manifold 1 4.7x1 Buna 70
Viking, Humphrey Solenoids with Adapter Manifold 1 6x1 Buna 70
Excalibur, Humphrey Solenoids 10 3.3x1 Buna 70
Viking, Humphrey Solenoids 5 3.3x1 Buna 70
Tornado Valve 2 015 Urethane 70
doc Zox is offline   Reply With Quote
Old 03-19-2008, 12:48 AM   #18 (permalink)
Post Whore
 
Join Date: Apr 2006

Quote:
Originally Posted by olinar View Post
Still leaked with these orings, I saw the thread where a member listed all teh orings needed in AKA markers and their size and all that.
I searched for online sellers that sell orings and they were a bit pricey at a buck a piece.

Any suggestions?
Well, darn. I was hoping for your sake the problem was just a damaged o-ring around the LPR. It is possible you have a problem inside your LPR. Recently, I had a problem similar to yours (leaking out the vent hole behind the Sidewinder. I finally had to replace the whole LPR. DBNPaintball had them for $25.00 shipped which was worth it to avoid rebuilding one.

custar
custar is offline   Reply With Quote
Old 03-19-2008, 01:04 AM   #19 (permalink)
Active Member
 
olinar's Avatar
 
Join Date: Feb 2007

Quote:
Originally Posted by NeoDriftOut View Post
OTe Web Store

They have it listed for 19.95 shipped for a complete parts kit.
That site seems to not have been updated in some time, The ad for the Viking/Excal rebuild reads "Get your Viking or Excalibur ready for the 2004 season" If this site is still good and has some merit I will probably have to pick this kit up if I find nothing else.
Quote:
Originally Posted by doc Zox View Post
Nitros How to disassemble and clean a viking - PbNation

AKA HOW TO: Viking Hammer Cartridge Disassembly - PbNation

O-rings used in AKA guns and SCM's - PbNation

Product Quantity Size Type Durometer
2 Liter 3 015 Urethane 70
2 Liter 2 009 Urethane 70
2 Liter 1 010 Urethane 90
2 Liter 1 019 Buna 70
2 Liter 1 017 Buna 70
Sidewinder 1 015 Urethane 70
Sidewinder 4 017 Buna 70
Sidewinder 1 113 Urethane 70
Sidewinder 1 008 Urethane 70
Sidewinder 2 010 Urethane 70
2004 Excalibur Ram 2 010 Quad Buna 70
2004 Excalibur Ram 5 015 Urethane 70
2004 Excalibur Ram 1 010 Urethane 70
2004 Excalibur Hammer 2 010 Quad Buna 70
2004 Excalibur Hammer 1 010 Urethane 70
2004 Excalibur Hammer 4 015 Urethane 70
2004 Viking Hammer 2 010 Quad Buna 70
2004 Viking Hammer 1 010 Urethane 70
2004 Viking Hammer 4 015 Urethane 70
Viking/Excalibur SCM-1 3 015 Buna 70
Viking/Excalibur SCM-1 1 014 Buna 70
Viking/Excalibur SCM-1 1 008 Urethane 70
Viking/Excalibur SCM-1 1 003 Buna 70
Viking/Excalibur SCM-1 2 015 Urethane 70
Merlin SCM-1 2 015 Buna 70
Merlin SCM-1 1 014 Buna 70
Merlin SCM-1 1 008 Urethane 70
Merlin SCM-1 1 003 Buna 70
Merlin SCM-1 1 013 Buna 70
Merlin SCM-2 1 015 Buna 70
Merlin SCM-2 1 014 Buna 70
Merlin SCM-2 1 008 Urethane 70
Merlin SCM-2 1 003 Buna 70
Merlin SCM-2 1 013 Buna 70
Matrix SCM-1 4 015 Buna 70
Matrix SCM-1 1 014 Buna 70
Matrix SCM-1 1 008 Urethane 70
Matrix SCM-1 1 003 Buna 70
Matrix SCM-1 1 009 Buna 70
Matrix SCM-2 3 015 Buna 70
Matrix SCM-2 1 014 Buna 70
Matrix SCM-2 1 008 Urethane 70
Matrix SCM-2 1 003 Buna 70
Matrix SCM-2 1 009 Buna 70
Timmy SCM-2 1 015 Buna 70
Timmy SCM-2 1 014 Buna 70
Timmy SCM-2 1 008 Urethane 70
Timmy SCM-2 1 003 Buna 70
Timmy SCM-2 1 020 Buna 70
Timmy SCM-2 1 115 Buna 70
Bushmaster SCM-2 1 015 Buna 70
Bushmaster SCM-2 1 014 Buna 70
Bushmaster SCM-2 1 008 Urethane 70
Bushmaster SCM-2 1 003 Buna 70
Bushmaster SCM-2 1 019 Buna 70
Bushmaster SCM-2 1 016 Buna 70
2003 Viking Hammer 5 015 Urethane 70
2003 Viking Hammer 1 013 Buna 70
2003 Viking Hammer 2 010 Buna 70
2003 Excalibur Ram 6 015 Urethane 70
2003 Excalibur Ram 2 010 Buna 70
2003 Excalibur Ram 1 013 Buna 70
2003 Excalibur Hammer 5 015 Urethane 70
2003 Excalibur Hammer 1 013 Buna 70
2003 Excalibur Hammer 2 010 Buna 70
Old LPR 3 015 Urethane 70
Old LPR 2 013 Buna 70
Old LPR 2 010 Buna 70
Old LPR 1 008 Buna 70
New LPR 3 015 Urethane 70
New LPR 1 013 Buna 70
New LPR 1 010 Buna 70
New LPR 1 008 Buna 70
New LPR 1 014 Buna 70
New Excalibur Bolt 2 015 Buna 70
Old Excalibur Bolt 2 015 Buna 70
Old Excalibur Bolt 1 013 Buna 70
Spring Holders 1 015 Buna 70
Excalibur Ram Plug Cap 1 015 Buna 70
Excalibur, Mac Solenoids 6 3.3x1 Buna 70
Viking, Mac Solenoids 3 3.3x1 Buna 70
Excalibur, Humphrey Solenoids with Adapter Manifold 6 3.3x1 Buna 70
Excalibur, Humphrey Solenoids with Adapter Manifold 2 3.5x1 Buna 70
Excalibur, Humphrey Solenoids with Adapter Manifold 2 4.7x1 Buna 70
Excalibur, Humphrey Solenoids with Adapter Manifold 2 6x1 Buna 70
Viking, Humphrey Solenoids with Adapter Manifold 3 3.3x1 Buna 70
Viking, Humphrey Solenoids with Adapter Manifold 1 3.5x1 Buna 70
Viking, Humphrey Solenoids with Adapter Manifold 1 4.7x1 Buna 70
Viking, Humphrey Solenoids with Adapter Manifold 1 6x1 Buna 70
Excalibur, Humphrey Solenoids 10 3.3x1 Buna 70
Viking, Humphrey Solenoids 5 3.3x1 Buna 70
Tornado Valve 2 015 Urethane 70
This is the listing I saw, I was unsure though as there arent too many listings for an 03 viking. Would they have all the same specs and internals as an 04?

Quote:
Originally Posted by custar View Post
Well, darn. I was hoping for your sake the problem was just a damaged o-ring around the LPR. It is possible you have a problem inside your LPR. Recently, I had a problem similar to yours (leaking out the vent hole behind the Sidewinder. I finally had to replace the whole LPR. DBNPaintball had them for $25.00 shipped which was worth it to avoid rebuilding one.

custar
That doesn't sound like a bad idea, but I'm hoping I just have the wrong size rings and need to find the proper ones. I might not be owning this viking too long as I need to use it as a bartering token to get me the parts I need to finish off my mag. Im hoping I can pick up some orings from Ace or somethin to keep my cost down...
olinar is offline   Reply With Quote
Old 03-19-2008, 04:00 AM   #20 (permalink)
Active Member
 
olinar's Avatar
 
Join Date: Feb 2007

I found a site that sells paintball orings specifically.
They dont however have a kit made up for anything AKA, seems to be just the very old companies they carry.

They have them cheap enough that I will just make up a list of all the ones I need for my marker and Ill order a couple sets.

Im not too sure they carry the urethane, Any chance itll work fine with the buna orings?
olinar is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » AKA

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 07:29 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC