mcarterbrown.com  

CCI Home of the Phantom Pump Gun

Reply
 
Thread Tools Search this Thread
Old 09-27-2012, 03:10 PM   #1 (permalink)
Active Member
 
Join Date: May 2012
Location: Nor Cal

Replacing the hardline

The hardline removed itself (due to pressure) from the bucket changer from the large nut. How do I place it back in? Do I remove the nut or just try to shove it back it?

Also is there any difference between macroline and hardline for Phantoms performance wise?
Duybuin is offline   Reply With Quote
Old 09-27-2012, 03:26 PM   #2 (permalink)
Stock Class Aficionado
 
idkfa's Avatar
 
Join Date: Mar 2007
Location: Vancouver, BC, Canada

CCM Fan
It did what now? If you are talking about the compression fittings, make sure the rubber seal is intact and screw the collars back on. Make sure your line stays straight though, if you tighten it down too much it can bend and leak.

No difference in performance, hardline is just dead sexy.
__________________
idkfa is offline   Reply With Quote
Old 09-27-2012, 03:41 PM   #3 (permalink)
Village Idiot
 
Greenmtnphantom's Avatar
 
Join Date: Jul 2006
Location: Graniteville VT
Send a message via AIM to Greenmtnphantom Send a message via MSN to Greenmtnphantom

Fan of EMR
No seriously what happened? The compression fitting came off due to pressure?
__________________
Feedback http://www.mcarterbrown.com/forums/f...-feedback.html Gargoyle FAQ http://isppa.semkhor.com/newswire.asp?ctid=1116
Quote:
Originally Posted by MaD View Post
Since this thread started with boobs what are we supposed to derail it with?
Stock class = 12grams and a stick feed. End discussion.
Greenmtnphantom is offline   Reply With Quote
Old 09-27-2012, 04:09 PM   #4 (permalink)
Stock Class Aficionado
 
idkfa's Avatar
 
Join Date: Mar 2007
Location: Vancouver, BC, Canada

CCM Fan
I think his Phantom exploded.

Step 1. Retrieve shards of CCI goodness from walls...
__________________
idkfa is offline   Reply With Quote
Old 09-27-2012, 04:28 PM   #5 (permalink)
Active Member
 
Join Date: May 2012
Location: Nor Cal

Was testing pressure with a 12 g and the hardline disconnected from the hexagonal looking piece. So my hardline is connected only to the rear of gun and floating
Duybuin is offline   Reply With Quote
Old 09-27-2012, 04:30 PM   #6 (permalink)
Active Member
 
Join Date: May 2012
Location: Nor Cal

I hadn't screwed the bucket changer back completely to trigger frame so it must've been awkwardly and vented the pressure
Duybuin is offline   Reply With Quote
Old 09-27-2012, 04:31 PM   #7 (permalink)
Stock Class Aficionado
 
idkfa's Avatar
 
Join Date: Mar 2007
Location: Vancouver, BC, Canada

CCM Fan
Whoa. What? Can you take a picture?

Did the hardline snap? The line itself fits inside that hexagonal collar, there is no way for it to slip out. It's too long.

Unscrew the collar and see what condition your hardline is in.
__________________
idkfa is offline   Reply With Quote
Old 09-27-2012, 04:33 PM   #8 (permalink)
Stock Class Aficionado
 
idkfa's Avatar
 
Join Date: Mar 2007
Location: Vancouver, BC, Canada

CCM Fan
Use this to illustrate if you have to:

__________________
idkfa is offline   Reply With Quote
Old 09-27-2012, 05:02 PM   #9 (permalink)
Active Member
 
Join Date: May 2012
Location: Nor Cal

Hard line slipped out of that right piece
Duybuin is offline   Reply With Quote
Old 09-27-2012, 05:06 PM   #10 (permalink)
Post Whore
 
Join Date: Aug 2007

undo the collar, slide the collar onto the hardine, put the rubber seal onto the hardline, then reassemble the gun and plug the hardline in place... then you need to push the collar and seal down towards the fitting, get the threads started, then tighten with a wrench.
ApoC_101 is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » CCI

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 10:44 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC