CCM Chipley Machine

Thread Tools Search this Thread
Old 07-29-2010, 02:39 AM   #1 (permalink)
Whats Paintball Gun? NOT
Join Date: Jun 2009
Location: Victoria BC Canada

CCM AIR FIttings Question

I got a new s6.5 with airfitting's

Kind of a dumb questions but how do I remove them?? I want to switch the sides of where the fitting is on the asa-on/off? also the side that does not have the fitting i can't remove any ideas
Lift-off Oversteer is offline   Reply With Quote
Old 07-29-2010, 07:55 AM   #2 (permalink)
...Not sure what that was
Disco's Avatar
Join Date: Feb 2009
Location: Niagara Falls

Well, i dont own a CCM marker...yet. But, from what ive seen in the other threads, and reading about the new fittings. Im going to say you take an allen key, and undo the screw on the fitting.

For the plug in the ASA, take a 3/16" allen key, and turn. Not sure if they use loctite or something on them during assembly, someone else can chime in on that one. But, a hair dryer on high can get the piece warm enough to crack it loose without any damage.
Dogs Forum, please subscribe

Originally Posted by Ieo View Post
I don't need it in my hands....the picture is right there. Cool thing about pictures: they give you an accurate representation of what something will look like. They've been doing it since 1822, or so I'm told.
Disco is offline   Reply With Quote
Old 07-29-2010, 08:53 AM   #3 (permalink)
post deleting ghost attak
Join Date: Feb 2008
Location: westchester NY

The plug should just have thread tape on it, and maybe some blue loctite, it shouldn't be to hard. And the fitting should have an allen key screw also.
duff muffin is offline   Reply With Quote
Old 07-29-2010, 09:32 AM   #4 (permalink)
suns out guns out
freebird's Avatar
Join Date: Jun 2008
Location: upstate NY
Send a message via AIM to freebird

If you have the new style air fittings they have been blue loc tighted in place. remove the visible allen screw and slide off the aluminum piece, leaving just the stainless shaft in the gun.
You will need to heat up the part slightly (hair dryer, heat gun) then remove the fitting. Insert your smallest allen key into the one of the 4 holes and use it to gain leverage to remove the fitting. When re-locating the fitting. A small ammount of blue loc-tight should be enough. Thread the shaft in finger tight then re-insert the allen key into the holes to tighten. DO NOT need to hulk the thing on there, just a little more than snug will be enough. Apply a little oil to the o-rings on the shaft/screw. slide the aluminum piece onto the shaft, apply a little blue loc tight on the retaining allen screw and re attach. Be sure to position the macro fitting in the correct direction before tightening down the screw.

Your best bet....
call CCM, tell them you need help with your fittings, Rod will walk you through how to do it. 1-877-412-6850
Originally Posted by John Wayne View Post
If you've got them by the balls their hearts and minds will follow.
MCB Feedback
AO Feedback

Hillbilly death machine.
Fuel'd by Diesel fuel, Miller High Life, Gunpowder, and Red Meat.
freebird is offline   Reply With Quote
Old 07-31-2010, 12:05 PM   #5 (permalink)
Whats Paintball Gun? NOT
Join Date: Jun 2009
Location: Victoria BC Canada

so new problem with air fittings.... They look great!!! but I wont seal on the macro line. I have pushed them in all the way, but as soon as I air up the gun the line shoots off. when I look at the macro line end it has a chunk missing from it. could the fitting be defective??
Lift-off Oversteer is offline   Reply With Quote
Old 07-31-2010, 12:18 PM   #6 (permalink)
1-113 Cav 2 BCT 34 ID
SPC. Cejka's Avatar
Join Date: Jun 2010
Location: Sioux City, Iowa
Send a message via MSN to SPC. Cejka Send a message via Yahoo to SPC. Cejka

is everyone have this problem?
SPC. Cejka is offline   Reply With Quote
Old 07-31-2010, 08:52 PM   #7 (permalink)
Post Whore
Spoon's Avatar
Join Date: Aug 2008
Location: Fort Collins, CO

I had the same problem when I first aired it up. It blew right off at the reg fitting. Then I degassed, shoved it back in, gave it a tug and then aired it up and it seemed fine. I didn't leave it connected for an extended amount of time. Just a minute or so.
Spoon is offline   Reply With Quote
Old 07-31-2010, 10:19 PM   #8 (permalink)
Red - Black
Talfuchre's Avatar
Join Date: May 2006

If you don't shove ANY macro fitting in tight - it will blow off - it uses pressure to seal.

Make sure she is in far.

Pumpenstein - NSA National Champions

TF's MCB Trust.
Talfuchre is offline   Reply With Quote
Old 08-01-2010, 08:11 PM   #9 (permalink)
Join Date: Jun 2010

So I played with my new T2 and fittings for the first time today. I aired it up with a 68/45 tank and no leaks at all. Then I tried using a 13/3000 and it leaked from both fittings. Reconnected the 68/45 and no leaks. Then tried my son's 45/45 and it leaked. Played the rest of the day with the 68 which never had a leak. So it looks like my fittings like a lot of volume. I'd like to be able to run the 13 ci for a lighter setup. Any suggestion?...and yes I'm planning on calling CCM first thing in the morning.
rheeep is offline   Reply With Quote
Old 08-01-2010, 10:11 PM   #10 (permalink)
Whats Paintball Gun? NOT
Join Date: Jun 2009
Location: Victoria BC Canada

upon closer inspection with some people a the west coast pump weekend in victoria. Their is a inner o-ring that might need to be replaced I will try this later tonight when I clean my gear I'll post if this has helped/made any difference to the leaking
Lift-off Oversteer is offline   Reply With Quote
Reply » Paintball » The Armory » CCM

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump

All times are GMT -4. The time now is 07:19 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC