mcarterbrown.com  

CCM Chipley Machine

Reply
 
Thread Tools Search this Thread
Old 09-26-2010, 03:03 PM   #1 (permalink)
Fluffy Bunnies for life!!
 
Jkoselka's Avatar
 
Join Date: Jul 2010
Location: State of Confusion

CCM Fan
Slider question

Got a question about the adjustments screws on a slider frame. Let me start by explaining what happened.

Saturday i was playing with my newly adopted S5 (thank you tacolex and CCM) and towards the end of the day of rplaying the trigger started to get really hard to pull. One thing that was going on were my macro-line fittings were leaky (which had nothing to do with the trigger) and then the trigger binding. I got the fittings squared away and then started to clean the trigger and gun. I did have a barrel break due to double pumping (doh!), which I guess could have jammed a shell into the trigger (maybe). After cleaning I backed the screw out that is on the bottom of the trigger guard and the trigger went back to its usual smooth self.

So I guess I am looking for any tips on how to avoid the binding in the future. I hadn't messed with the adjustment screw before or during play so would be it be normal for it to tighten up?

Any thoughts or ideas welcome. Thanks!
__________________
America is all about speed. Hot, nasty, bada$$ speed. -Eleanor Roosevelt, 1936
FLUFFY BUNNIES PUMP

Ebay Feedback
MCB Feedback
Jkoselka is offline   Reply With Quote
Old 09-26-2010, 03:42 PM   #2 (permalink)
WVU paintball #19
 
minimag03's Avatar
 
Join Date: Aug 2006
Location: Morgantown, WV

AKA Fan
There should be a second adjustment screw where your middle finger rests on the frame. It might be under the grips. Make sure both the screws are adjusted to the same height and that they aren't so tight that the trigger binds. If your problems persist, you might need a heavier trigger spring.
minimag03 is offline   Reply With Quote
Old 09-26-2010, 07:37 PM   #3 (permalink)
Red
 
Talfuchre's Avatar
 
Join Date: May 2006

CCM Fan
Not heavier springing - the springing is fine.

Take the frame apart and clean it first. If there is grit in the frame - it can make a mess. Take out the trigger - make sure the sides are flat and even - if not - use 2000 grit sandpaper wet and sand them flat again.

Put it all back together and make sure (like the post above says) to adjust the rear trigger adjustment screw to make sure it is not binding on the trigger.

TF
__________________
Pumpenstein - NSA National Champions

TF's MCB Trust.
Talfuchre is offline   Reply With Quote
Old 09-26-2010, 08:05 PM   #4 (permalink)
Fluffy Bunnies for life!!
 
Jkoselka's Avatar
 
Join Date: Jul 2010
Location: State of Confusion

CCM Fan
I figured that a little chunk of something had gotten itself up inside. Just the advice I was lookin for.Thanks!
__________________
America is all about speed. Hot, nasty, bada$$ speed. -Eleanor Roosevelt, 1936
FLUFFY BUNNIES PUMP

Ebay Feedback
MCB Feedback
Jkoselka is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » CCM

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 10:56 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC