mcarterbrown.com  

CCM Chipley Machine

Reply
 
Thread Tools Search this Thread
Old 04-30-2013, 10:24 AM   #1 (permalink)
Active Member
 
DevilMayCare's Avatar
 
Join Date: Jun 2012
Location: Dallas, TX

Stripped top-tube screw in T2

My T2 is pretty filthy and I was going to give her a complete cleaning. I wasn't paying attention, grabbed a T9 instead of a T10 and stripped out the screw that's directly down the feed-neck.



It's stripped enough that the t10 doesn't get a good grip, so I stopped messing with it (at only 38 I've finally learned when to stop digging) and came here.

Any thoughts on a safe way to get it out? Or should I just contact Mel and send it in for professional help?

Gracias.
DevilMayCare is offline   Reply With Quote
Old 04-30-2013, 10:32 AM   #2 (permalink)
Formerly lancecst
 
BLachance75's Avatar
 
Join Date: Sep 2006
Location: Western Mass

CCM Fan
You could try an Allen wrench. You could also try heating it a little because I believe they use loctite on that screw.
__________________
BLachance75 is offline   Reply With Quote
Old 04-30-2013, 10:55 AM   #3 (permalink)
Rubber Duckie/Ninja Squad
 
Join Date: Aug 2010
Location: New home at OSG

You could try a "ball-end" allen wrench on it, or if available, a very small "easy-out" designed to remove stripped screws and such. Usually a hardware store will have them...
JMac is offline   Reply With Quote
Old 04-30-2013, 11:01 AM   #4 (permalink)
Formerly Floundah
 
MEDuck's Avatar
 
Join Date: Feb 2012
Location: Maine

CCM Fan
Superglue a t10 to it, let it set for a few days, try removing that's about the extent of my knowledge
MEDuck is offline   Reply With Quote
Old 04-30-2013, 12:18 PM   #5 (permalink)
Red
 
Talfuchre's Avatar
 
Join Date: May 2006

CCM Fan
Easy out may not be long enough - that may be your issue there.

TF
__________________
Pumpenstein - NSA National Champions

TF's MCB Trust.
Talfuchre is offline   Reply With Quote
Old 04-30-2013, 12:37 PM   #6 (permalink)
MCB Member
 
Join Date: Oct 2007

CCM Fan
If all else fails send me just the body and I will take it out for you.
__________________
“Do not yearn too much for a sword made by a famous smith. This is because even if you give a good man a sword worth ten thousand coppers, he will not be able to beat a hundred men each holding a spear worth a hundred coppers.” - Asakura Takakage Toshikage, 1462-1482

Ecc. 9-10
Whatever your hand finds to do, do it with your might; for there is no work, nor device, nor knowledge, nor wisdom, in the grave, where you go.

DOOR GUNNER handgun mounts for gunsafes.

http://www.machineshopdpm.com/
CCMachinist is offline   Reply With Quote
Old 05-03-2013, 10:17 AM   #7 (permalink)
Rubber Duckie/Ninja Squad
 
Join Date: Aug 2010
Location: New home at OSG

Quote:
Originally Posted by Talfuchre View Post
Easy out may not be long enough - that may be your issue there.

TF
Very true, although removing the feedneck "might" give the little extra length.
So, how'd you make out with said project? Just curious...
JMac is offline   Reply With Quote
Old 05-03-2013, 12:32 PM   #8 (permalink)
Active Member
 
DevilMayCare's Avatar
 
Join Date: Jun 2012
Location: Dallas, TX

Quote:
Originally Posted by JMac View Post
Very true, although removing the feedneck "might" give the little extra length.
So, how'd you make out with said project? Just curious...
Been jammed up at work all week, waiting for the weekend to give it a go.
DevilMayCare is offline   Reply With Quote
Old 05-03-2013, 08:25 PM   #9 (permalink)
A.B.K.
 
SOGAmember666's Avatar
 
Join Date: Jan 2008
Location: Columbus, GA

CCM Fan
Your marker is completely broken. I'll give you $5 for it. Lol

I'd remove feed neck and use an easy out bit. I had to use one when I snapped a transmission bolt. Saved me about $200 from the stealership. Obviously this is different but if you haven't used it before its quite straight forward.
SOGAmember666 is offline   Reply With Quote
Old 05-11-2013, 09:16 PM   #10 (permalink)
Active Member
 
DevilMayCare's Avatar
 
Join Date: Jun 2012
Location: Dallas, TX

Had to take the feed neck off and enlist the help of a friend who's used an easy-out before, but we managed to get it out. Only took a few minutes.

Thanks for the suggestions and help!
DevilMayCare is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » CCM

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 07:25 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC