mcarterbrown.com  

CCM Chipley Machine

Reply
 
Thread Tools Search this Thread
Old 06-03-2014, 10:04 PM   #1 (permalink)
Hawkeye: Finest Kind
 
Marathon's Avatar
 
Join Date: Nov 2009
Location: Suburbs of Toronto

CCM Fan
T2 disassembly problems

I want to send out my T2 for anno. I cannot get a couple of parts disassembled.

How do you remove both pump arms from the pump handle? The arm with the AT on it is easy enough to remove. The other (right) arm has nothing to grip. Any tips on removing the right pump arm? Preferably without scaring the heck out of it.

How do you separate the feedneck from the part that attaches the feedneck to the top tube? I can remove the clamping ring easy enough but the other two parts of the feedneck won't come apart? I have tried hot water and swearing at it. These have been ineffective.
Thanks
__________________
Feedback
M.CarterBrown
Custom Cockers
Marathon is offline   Reply With Quote
Old 06-04-2014, 01:16 AM   #2 (permalink)
Vieux.
 
Allblack's Avatar
 
Join Date: Jun 2009
Location: Lyon, France

CCM Fan
Pump arms are not supposed to be removed. You may have to ask Rod.
To remove the feedneck, lock a hopper in and turn.
__________________

Allblack is offline   Reply With Quote
Old 06-04-2014, 02:15 AM   #3 (permalink)
Surfing MCB
 
pakalolo's Avatar
 
Join Date: Mar 2009
Location: NoR CaL

CCM Fan
Palmers Fan
call ccm or if you have these basics tools you can DIY


2 penny's, vice grips and a lighter is what you will need for the rods,
a strap wrench and lighter to separate the mounting plate for the feed neck

rod removal take two penny's sandwich the rod with them and clamp them down with vice grips the penny's will keep you from damaging the rod then use the lighter to heat the rod where it meets the pump plate this will loosen the loctite and dont worry the lighter will not effect the anno then unscrew the rod

Feedneck removal
use the lighter again to heat the neck where it meets the mounting plate with feed neck so it will loosen the red loctite used from factory then with the feedneck attached to the gun use a strap wrench to separate the neck from the mounting plate or lock a hopper tight and turn

on reassemble of RODS its very important you make sure the lengths are even most ppl mess this up and it will effect the stoke! ROD @CCM takes the essence of perfection when he builds t2's ensuring rods are equal and binding is non existent upon assemble

Last edited by pakalolo; 06-04-2014 at 02:27 AM.
pakalolo is offline   Reply With Quote
Old 06-04-2014, 04:44 PM   #4 (permalink)
MCB Member
 
Join Date: Apr 2007
Location: Charlottesville, VA

CCM Fan
Nothing like taking a blow torch to a ccm, Ive never been so careful in my life.
__________________
Feedback
BIG BOB is offline   Reply With Quote
Old 06-04-2014, 08:49 PM   #5 (permalink)
Red
 
Talfuchre's Avatar
 
Join Date: May 2006

CCM Fan
Vice grips and dremel tools FTW.

TF
__________________
Pumpenstein - NSA National Champions

TF's MCB Trust.
Talfuchre is online now   Reply With Quote
Old 06-04-2014, 09:36 PM   #6 (permalink)
MCB Member
 
Slappadapink's Avatar
 
Join Date: Nov 2012
Location: Ottawa, Ontario

Quote:
Originally Posted by Talfuchre View Post
Vice grips and dremel tools FTW.

TF
I'm going to go listen to Carrie Underwood's "Jesus take the wheel" and cry now.
Someone's definitely done it. I Just looked at my wife's T2 and decided that I shouldn't be allowed near it with tools.
__________________
Feedback
Slappadapink is offline   Reply With Quote
Old 06-04-2014, 10:10 PM   #7 (permalink)
Formerly lancecst
 
BLachance75's Avatar
 
Join Date: Sep 2006
Location: Western Mass

CCM Fan
I prefer using Channel Locks over vice grips. The Channel Locks slip more and do more damage.

The penny idea is actually really good. I'm going to try that next time I have to take a pump arm off.
__________________
BLachance75 is offline   Reply With Quote
Old 06-04-2014, 10:37 PM   #8 (permalink)
MCB Member
 
Join Date: Apr 2007
Location: Charlottesville, VA

CCM Fan
It apparently also works if you ever need to take the pump guide rods off also, was about to do it prior to an ano job but ended up selling the marker instead.
__________________
Feedback
BIG BOB is offline   Reply With Quote
Old 06-04-2014, 11:15 PM   #9 (permalink)
Phone winner.
 
El Super Beasto's Avatar
 
Join Date: Jan 2010
Location: Halifax, Nova Scotia

A pot of boiling water is a good alternative to fire.
El Super Beasto is offline   Reply With Quote
Old 06-06-2014, 07:08 PM   #10 (permalink)
Hawkeye: Finest Kind
 
Marathon's Avatar
 
Join Date: Nov 2009
Location: Suburbs of Toronto

CCM Fan
Thanks for the suggestions guys. I never would have thought of the penny trick. I like to know I am doing the right thing before I really start torquing on something. I have a couple of extra T2 pump handles to experiment on before I attempt the one I want to anno.

TF: Suggesting you take a dremmel to a CCM Product. You should ban yourself for that sacrilege.
__________________
Feedback
M.CarterBrown
Custom Cockers
Marathon is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » CCM

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 11:15 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC