mcarterbrown.com  

Custom Projects / Custom Questions How do I customize? What do I customize? What do I use? Share you experiences and faults here!

Reply
 
Thread Tools Search this Thread
Old 06-10-2011, 01:52 AM   #1 (permalink)
Fire power
 
Join Date: Oct 2010
Location: CA

Single trigger frame EP Mag/ Oldschool EP sleeper.

Parts so far.

New AGD AM/MM rail
Aluminum Single AGD trigger frame
Universal T Board kit
SMC Noid (S070C-SDG-32)
MPA3 Ram
PPS Micro Rock LPR
Remote line adaptor


The general layout I will make an aluminum sleeve for the LPR and put a bike grip on it so it will look oldschool.


After some milling on the drill press and we are looking good.

This is a shot of where the micro switch will go


I had to shorten the trigger safety arm on the trigger so I could fit the switch in the frame and get room for the ram. This part of the trigger is what activates the switch. The second pic is what it looks like inside the marker.



The dry fit and it all fits nicely.


This is what I will use to do my soldering. A portasol Butane soldering unit.

Last edited by Hill160881; 06-11-2011 at 12:58 PM.
Hill160881 is offline   Reply With Quote
Old 06-10-2011, 01:57 AM   #2 (permalink)
Fire power
 
Join Date: Oct 2010
Location: CA

Now the layout with the lpr. I cant wait to see it with the bike grip on it.


I am working on the wiring. It is slow going but it is looking clean. Noid, microswitch, and battery terminal is good, now all I need to do is the membrane pad and LED.

The wires after separation. Also a shot of the wires I removed from the plug because I wont be using them. This way I can put them back in if I ever decide to do eyes.



The micro-switch was soldered very close so I could cut off the extra length on the prongs. This way it fits where I want it without messing with the ram position.


With the noid, switch and battery installed and no rats nest of wires I make it look easy but it just takes time and experience to get things to look clean.

Last edited by Hill160881; 06-11-2011 at 12:46 PM.
Hill160881 is offline   Reply With Quote
Old 06-10-2011, 10:28 AM   #3 (permalink)
MCB Member
 
Spider!'s Avatar
 
Join Date: Dec 2008
Location: Houston, TX

Just a remimder. Don't forget that when you're laying out the inside of the frame, leave room for your hoses, wires, and wiring connectors. It's a substantial amount of space, relative to what is available.

In considering such a project, I finally gave up on putting the battery in the frame. I kind of like the idea of using a pair of cheap cell phone batteries (like a BT60), with one in each (custom) grip panel. I haven't tested the noid and circuits on that setup though. Solder some wires on the batteries and have Robertsr mold them in (with new screw holes). These projects would be so much cleaner without hoses and wires.

Looking forward to your results anyway.
__________________
My Feedback

some things are stickier than others
Spider! is offline   Reply With Quote
Old 06-10-2011, 11:26 AM   #4 (permalink)
Fire power
 
Join Date: Oct 2010
Location: CA

I will be removing any extra wires from the plug so I only need 9 lines to the board. The noid(2), the switch(2), Battery(2), and the button pad(3). It will be a tight, but I think/hope it will all fit.
Hill160881 is offline   Reply With Quote
Old 06-10-2011, 02:00 PM   #5 (permalink)
Back to paintball.
 
Ir0nExpress's Avatar
 
Join Date: Apr 2006
Location: New York
Send a message via AIM to Ir0nExpress

You could hollow out the AGD rubber grips so you get more wiring space.
Ir0nExpress is offline   Reply With Quote
Old 06-10-2011, 10:18 PM   #6 (permalink)
Active Member
 
Join Date: May 2008

Hollow out the grips/have some one make you custom ones. This will let you get a bit of wiggle room

Alternatively you could make a front "battery pack" that houses everything but the noid/pnuematics
Matt Ribble is offline   Reply With Quote
Old 06-10-2011, 10:51 PM   #7 (permalink)
MCB member U MEMMMBER?
 
oldskoolkillz's Avatar
 
Join Date: Feb 2010
Location: So.California

Quote:
Originally Posted by Matt Ribble View Post
Hollow out the grips/have some one make you custom ones. This will let you get a bit of wiggle room

Alternatively you could make a front "battery pack" that houses everything but the noid/pnuematics
emag?
__________________
Don't mess with the OLD ones.....
collecting another few mags for my Gun WHORE status!!
I ship fast & pay on time....everytime!!
FEEDBACK :http://www.mcarterbrown.com/forums/f...ml#post1194437[url]
PAYPAL: PREMIUM VERIFIED USER
our work halloween pic as my Avi.......
oldskoolkillz is offline   Reply With Quote
Old 06-11-2011, 12:00 AM   #8 (permalink)
Fire power
 
Join Date: Oct 2010
Location: CA

I got loads of room Everything fits with room to spare. I will be putting the LED in there to, maybe.

New pics at the top

Last edited by Hill160881; 06-11-2011 at 12:50 AM.
Hill160881 is offline   Reply With Quote
Old 06-11-2011, 12:20 PM   #9 (permalink)
Active Member
 
Join Date: May 2008

How are you mounting your grips?
Matt Ribble is offline   Reply With Quote
Old 06-11-2011, 12:33 PM   #10 (permalink)
Fire power
 
Join Date: Oct 2010
Location: CA

Drill and tap new holes

New pics at top

Last edited by Hill160881; 06-11-2011 at 12:41 PM.
Hill160881 is offline   Reply With Quote
Reply

  mcarterbrown.com » Custom » Custom Projects / Custom Questions

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 09:53 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC