mcarterbrown.com

mcarterbrown.com (http://www.mcarterbrown.com/forums/)
-   Custom Projects / Custom Questions (http://www.mcarterbrown.com/forums/custom-projects-custom-questions/)
-   -   DIY Mag fed marker - TX1 (Warning: picture intensive) (http://www.mcarterbrown.com/forums/custom-projects-custom-questions/236905-diy-mag-fed-marker-tx1-warning-picture-intensive.html)

Typhon 07-03-2013 02:24 AM

DIY Mag fed marker - TX1 (Warning: picture intensive)
 
Hey all, first post here so I thought I would try and make it a good one..

This is my first attempt at a mag fed marker, for simplicity sake I decided to use an existing platform and adapt it to suit. In retrospect I actually increased the complexity of the project by going this route, but live and learn.

Project TX1 was started September 2012.

Main goals of this project are as follows:
  • AR platform, compatible with most standard AR furniture (MAGPUL YAY)
  • Electro - but must not appear to be. Needs eyes, doesn't need blinking lights
  • Better mag fitment than available mag fed markers (sorry milsig/Rap4, I don't like wobbly mag wells)
  • Very few visible fasteners (MUCH harder than it sounds)

I chose the BT TM7/TM15 internals. I liked the simple engine design, low pressure operation, AC threaded body, and small electronics footprint.


Machining day 1, September 23rd, 2012: Lower receiver begins

Turned a blank on the manual lathe and loaded it into the 4 Axis vertical milling machine. Bonus points if someone out there recognizes the brand of machine...

Note: The machine had a bad Y-axis ball screw at the time, which caused some unwanted vibration :(

http://i1297.photobucket.com/albums/...pse482e35d.jpg


http://i1297.photobucket.com/albums/...ps19db57a5.jpg


http://i1297.photobucket.com/albums/...pse8e241d3.jpg


http://i1297.photobucket.com/albums/...ps559bbf4d.jpg


http://i1297.photobucket.com/albums/...ps303ac0de.jpg



http://i1297.photobucket.com/albums/...psfe264488.jpg


Then I bought a house... and didn't work on it again until late November / early December.


http://i1297.photobucket.com/albums/...ps374c5e9e.jpg


http://i1297.photobucket.com/albums/...ps674b3d3f.jpg


http://i1297.photobucket.com/albums/...psc209dc73.jpg


http://i1297.photobucket.com/albums/...ps0224cedd.jpg


http://i1297.photobucket.com/albums/...ps642f273c.jpg


http://i1297.photobucket.com/albums/...ps648af369.jpg


http://i1297.photobucket.com/albums/...psc719b2f1.jpg


http://i1297.photobucket.com/albums/...pseef21cd2.jpg


http://i1297.photobucket.com/albums/...psd2fa496b.jpg


http://i1297.photobucket.com/albums/...ps75ca2909.jpg


http://i1297.photobucket.com/albums/...ps2bba7174.jpg


http://i1297.photobucket.com/albums/...ps8a25e522.jpg


http://i1297.photobucket.com/albums/...ps8a98056b.jpg


http://i1297.photobucket.com/albums/...ps789d51ea.jpg


http://i1297.photobucket.com/albums/...psed513ef5.jpg


Below you can see the general layout of the marker, the BT TM portion is rotated upside down, and the solenoid protrudes from the bottom of the upper receiver into the lower receiver. The circuit board is at the top of the TM body. The original plan was to use a 13cui tank, but due to time constraints that plan was later dropped in favor of a remote line.

http://i1297.photobucket.com/albums/...ps152fc2aa.jpg


Now at this point the lower receiver is still only 80% finished..this is important later. I get bored easily so I move on to the upper receiver. Date on these photos ranges from December 8 - 18th, 2012.

Same sort of idea as the lower, turn a blank on the manual lathe, bore to fit the TM7 body, mill on the VMC until crispy brown. Enjoy.

http://i1297.photobucket.com/albums/...ps50ef0886.jpg


http://i1297.photobucket.com/albums/...ps94b876bf.jpg


http://i1297.photobucket.com/albums/...ps6fb85c55.jpg

Solenoid poking out

http://i1297.photobucket.com/albums/...ps9393ab9a.jpg

First picture of a semi assembled state. Mag inserts, and ejects paintballs into the TM7 breach. December 18th, 2012.

http://i1297.photobucket.com/albums/...ps0753484c.jpg

Project took a 4 month hiatus after my daughter was born, and once I had enough sleep to think again I got back at it.

Now my decision to use a existing part starts to bite me in the a$$. Some of the parts I have drawn in solidworks turn out to be better in theory than in practice... or rather hard to machine.

Example #1: The T handle, and top slide. Originally I designed the T-handle to both turn the marker on when pulled back, and turn the air off.. WAAAAAAY too complicated. Quick redesign, now it turns the marker on only.

The other piece pictured is the top slide which guides the T-handle,closes up the upper receiver and mounts the RIS rails. It was originally designed as 1 piece with a rectangular cutout for the T-handle. It is very thin, in spots less than .100". Another redesign, and it was split into 2 pieces.

http://i1297.photobucket.com/albums/...ps2a7c22fc.jpg


http://i1297.photobucket.com/albums/...ps931e4db9.jpg


http://i1297.photobucket.com/albums/...ps7179886b.jpg

Example #2: Built in LPR
Remember that 80% complete lower receiver? The reason it was 80% complete was because the original design called for the low pressure regulator to be built into it, along with the ASA for the tank-in-stock. Needless to say I opted out of the idea, designed a separate LPR to thread into the back of the lower receiver using the standard AR buffer tube thread (1 3/16"-16UN 3B Mil-STD).

Slapped a rail and scope on the top for reference, but pay attention to the back of the lower receiver.

http://i1297.photobucket.com/albums/...ps8300f6eb.jpg

BAM! Threadmilled.
http://i1297.photobucket.com/albums/...ps35ad598c.jpg


Added an NPT port to the top slide end (the second portion of the top slide)

I have to point it out, as a machinist it bugs the hell out of me.. but there was a mistake I made on the lower receiver and a tool offset was .01" instead was a .001" which gives a nice little gap between the back of the upper receiver and the lower.:censored::banghead:
General tolerance for the marker is +/- .005", slide fits are generally within .001"

http://i1297.photobucket.com/albums/...ps72a5c5ad.jpg

http://i1297.photobucket.com/albums/...pse6154f8d.jpg


My original design also called for a rifle length 1 piece shroud, also referred to as "11.5 inches of how the hell do I machine that..". I reconsidered, and went with 6.5" carbine length instead LOL


June 2nd, 2013
http://i1297.photobucket.com/albums/...ps2163cdd0.jpg

http://i1297.photobucket.com/albums/...ps85aa810e.jpg

http://i1297.photobucket.com/albums/...ps2556acac.jpg

http://i1297.photobucket.com/albums/...ps9a152b3c.jpg

http://i1297.photobucket.com/albums/...ps19bfe066.jpg

http://i1297.photobucket.com/albums/...psc941caac.jpg

http://i1297.photobucket.com/albums/...ps93498ba3.jpg


http://i1297.photobucket.com/albums/...ps3df3fb74.jpg


And that's where I'm at now. Any questions or comments are always appreciated, thanks for looking!

Typhon 07-03-2013 02:25 AM

*reserved for later info/pics*

Keebler 07-03-2013 02:33 AM

Ha i dig it!

bond commander bond 07-03-2013 03:19 AM

RJF meets mag fed paintball?
 
RJF meets mag fed paintball? Quite the project.:bowdown

bob_wuzza 07-03-2013 08:11 PM

Just wow....

need4reebs 07-03-2013 08:26 PM

oh hells yeah!!! very nice!!

suaze 07-03-2013 10:06 PM

Congrats on surviving the early months of parenthood and great job on the gun.

RatFink 07-03-2013 10:22 PM

Awesome work. Please tell me you are going to have it clear annoed.

Christacular 07-04-2013 01:39 AM

that is pure awesome

TPX 07-04-2013 08:01 AM

Great work man! That's really really nice


All times are GMT -4. The time now is 07:24 AM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO
© MCB Network LLC