mcarterbrown.com

mcarterbrown.com (http://www.mcarterbrown.com/forums/)
-   Dealers Forum (http://www.mcarterbrown.com/forums/dealers-forum/)
-   -   SSC GOG Enemy Trigger Rockets - IN STOCK and ready to ship! (http://www.mcarterbrown.com/forums/dealers-forum/239365-ssc-gog-enemy-trigger-rockets-stock-ready-ship.html)

super_stanchy 08-06-2013 10:12 PM

SSC GOG Enemy Trigger Rockets - IN STOCK and ready to ship!
 
Finally finished off the first run!

I have 90 in stock and ready to ship.

These drop right into the GOG Enemy

They use a 4-40 Setscrew (included) for full adjustment

http://i169.photobucket.com/albums/u...ps9921cddf.jpg

https://fbcdn-sphotos-g-a.akamaihd.n...30926666_o.jpg

Price:
$15.00 + S&H

S&H
$2.50 USA
$5.00 International




Installation:
Degas Marker
Unscrew regulator
Undo one side of the grip grame
Undo both of the frame screws
Undo the banjo fitting
*Frame should be free at this point*
Push the existing Rocket upwards, it will push through the hole and pop out
Insert SSC Enemy Rocket

Reassemble following same steps as above

Fine Tuning:
Use a .050" allen wrench
-Unscrew to shorten the stroke
-Screw in to lengthen the stroke

-Stanchy

*pictures and final count once i get the setscrews installed!*

neftaly 08-06-2013 11:12 PM

Quote:

The Trigger Rocket is precision engineered from aluminium alloy and is designed to significantly improve trigger characteristics on the GOG™ eNMEy™. When used with a shim, trigger pull can be shortened by up to 70% and trigger slop dramatically improved.

• Made in the USA
• Fully adjustable
• Replaces plastic NME104 Actuator Pin
• Allows 1/8" trigger pull to be shortened to as little as 1/32" (with shim)

http://i.imgur.com/N5ExnRP.pnghttp://i.imgur.com/qJKTc1R.jpghttp://i.imgur.com/YYmIxih.jpg
http://i.imgur.com/pZ7VcFO.jpg

Tuning your Trigger Rocket:
The suggested Rocket length (tip to tip) is 5/8".

To tune your trigger pull to the minimum possible length, back out the screw on the Rocket a few turns, put the safety on and re-assemble your eNMEy.

With the safety still on, gas up and pull the trigger. Give it a fair tug, but not too hard - you don't want to snap the plastic trigger. The marker will likely vent air, and may even fire.

Disassemble the marker, screw in the adjuster a quarter turn, and reassemble the marker.

Repeat until it no longer vents air when the trigger is pulled with the safety engaged.


Shim:
The Trigger Rocket is designed to remove travel after the safety engagement point. The screw must not be over-extended, as it will prevent the safety from operating correctly. To safely remove travel in front of the safety engagement point, a shim is required.

You will need:
• ~ 1" x 1/2" strip of 1/32" or 1mm thick Aluminium sheet (recommended) OR an old credit card.
• 1/2" strip of double-sided adhesive tape
• Scissors

http://i.imgur.com/UMO1z5Y.png

1. Cut and fold the shim to the template above.

2. Leaving the protective backing in place, apply double-sided tape to the inside of the long side.

3. Remove the grip panel, and slide in the shim underneath the trigger. The short side should sit at the front.

4. Remove protective adhesive backing, wedge the trigger forward and fix shim against frame.

super_stanchy 08-06-2013 11:35 PM

oh!

i will have each Rocket set to about .615" OAL

which is a little short, but should be good enough start for you guys!

4G010H3R0 08-07-2013 12:13 AM

finally :p

Message sent

super_stanchy 08-07-2013 12:52 AM

4G... pm'd you
Merc... pm'd you!

super_stanchy 08-07-2013 12:54 AM

Rockets
 
Here ya go!

Price:
$15.00 + $2.50 S&H

paypal is r.stanchfield@comcast.net

let me know when its sent, and i'll get it out the door!


Quote:

Originally Posted by Mercenario (Post 2774675)
I'll take one


PistolRogue 08-07-2013 02:06 AM

Nice, and awesome pricing to boot! Sending payment shortly

Mercenario 08-07-2013 09:44 AM

Ok Neftaly ;)

Sending payment

potts213 08-07-2013 10:45 AM

Pm and payment sent!

Deathwish_DW 08-07-2013 11:18 AM

Awesome!


All times are GMT -4. The time now is 02:10 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC