New Paintball Pistol Holsters F/S - Page 2

Titus · 03-30-2008, 12:08 AM

Smiley, you sent it to my parents address since we've been having that issue with me getting MOs from you correct?

These are right handed.

Morfesto · 03-30-2008, 02:02 PM

Unless the pictures are inverted it looks like it should got on the left side of your body to have the grip of the pistol oriented in a way you can actually draw it, which would be with your left hand?

Do you have any pics of it in use?

Titus · 04-18-2008, 03:33 PM

I have in stock at the moment both left and right handed pistol holsters.

Anyone interested, please PM me.

Mayvik · 04-21-2008, 05:56 PM

How snug are these on the PGP? Looking for a holster for a PGP Stroker, but not sure if it will be too tight with the pneumatics..

Titus · 04-22-2008, 04:58 PM

Pre or post 2k?

Mayvik · 04-22-2008, 05:29 PM

Uh..it's a pre but it's got a new barrel and tube cut to the length of the bottom tube with the Fassst installed so I'm assuming it's total length is now probably the same as a 2k1 barrel. I was more worried about the width, didn't even think about the length difference.

Titus · 04-22-2008, 05:56 PM

PM sent

Mayvik · 04-30-2008, 03:20 PM

For anyone interested, these holsters are wide enough to accommodate the pneumatics, and the end is open, so it will accept markers with 3 stacked tubes longer than a PGP. My PGP Stroker fits fine and it appears that they will also hold a Squall as well.

dundadun · 05-01-2008, 02:47 AM

also holds tac8s fine too

Kyote · 05-01-2008, 09:25 PM

Will this holster hold a splatmaster?

03-30-2008, 02:02 PM	#12 (permalink)
Morfesto Canuck Join Date: Nov 2007 Location: Ottawa, On.	Unless the pictures are inverted it looks like it should got on the left side of your body to have the grip of the pistol oriented in a way you can actually draw it, which would be with your left hand? Do you have any pics of it in use? __________________ Spyder Aggressor -- Palmer stab - milled for timmy bolt Automag -- ULE body - Q-loader - Logic 90° frame Pump Autococker -- Palmer Fatty stab - WWA pump kit PGP -- Kframe - Quick Changer - CooperT Bolt KP2 -- Performance tune and side tube re-addition by Dan Sergison PMI-1 -- Mint

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

04-21-2008, 05:56 PM	#14 (permalink)
Mayvik 1-866-MEAT-4-YU Join Date: May 2007 Location: Binghamton NY	How snug are these on the PGP? Looking for a holster for a PGP Stroker, but not sure if it will be too tight with the pneumatics..

04-22-2008, 05:29 PM	#16 (permalink)
Mayvik 1-866-MEAT-4-YU Join Date: May 2007 Location: Binghamton NY	Uh..it's a pre but it's got a new barrel and tube cut to the length of the bottom tube with the Fassst installed so I'm assuming it's total length is now probably the same as a 2k1 barrel. I was more worried about the width, didn't even think about the length difference.

04-30-2008, 03:20 PM	#18 (permalink)
Mayvik 1-866-MEAT-4-YU Join Date: May 2007 Location: Binghamton NY	For anyone interested, these holsters are wide enough to accommodate the pneumatics, and the end is open, so it will accept markers with 3 stacked tubes longer than a PGP. My PGP Stroker fits fine and it appears that they will also hold a Squall as well.

05-01-2008, 02:47 AM	#19 (permalink)
dundadun Active Member Join Date: Jul 2007	also holds tac8s fine too

05-01-2008, 09:25 PM	#20 (permalink)
Kyote Rec Poster Join Date: Apr 2008 Location: San Marcos, TX	Will this holster hold a splatmaster?