New H8TR thread - Page 3

John Satclaire · 05-15-2008, 07:06 PM

Pack long soccer socks, plenty of flawed recievers
Fly to erring machinist's shop
Locate said machinist
Place reciever(s) into sock(s)
Beat the out of said machinist with flawed reciever in a sock

davidwirth · 05-17-2008, 10:17 PM

I have the sample put together. The trigger pieces all click so it sounds good. I am really really scared to gas it up.

Sly1 · 05-17-2008, 10:35 PM

um, what is the H8ter? I'm sure there is a thread describing it.. but I searched for one.. and couldn't find it.

any pictures?

Walker · 05-17-2008, 10:47 PM

Quote:

Originally Posted by Sly1

um, what is the H8ter? I'm sure there is a thread describing it.. but I searched for one.. and couldn't find it.

any pictures?

I think the long wait is almost over for the H8TR

Walker

Walker · 05-17-2008, 10:48 PM

Quote:

Originally Posted by davidwirth

I have the sample put together. The trigger pieces all click so it sounds good. I am really really scared to gas it up.

Wooooo! Hoooooo!!!!!

Walker

Brewtt · 05-19-2008, 11:19 AM

Quote:

Originally Posted by davidwirth

I have the sample put together. The trigger pieces all click so it sounds good. I am really really scared to gas it up.

Ummm... gas it up.

John Satclaire · 05-19-2008, 12:04 PM

Quote:

Originally Posted by davidwirth

I have the sample put together. The trigger pieces all click so it sounds good. I am really really scared to gas it up.

FIRST set up the video gear, THEN gas it up!

John Satclaire · 05-20-2008, 02:31 PM

Dave, oh Daaaaaveeee...

have you gassed it up yet?

davidwirth · 05-20-2008, 07:32 PM

Yeah, still got a problem with hole location the hole where the sear roller sits (the one that was .03 off) has been fixed. It sort of fires but then is slow on the rebound because the valve arm is not pushing the 4-way in. Also there was some leaking problems but I think the problem with that was the shaft and the cup. The shaft was backing out of the cup causing the hammer to push against it. For some reason the loc-tite never set. So I have reloctited it and will try again. It did make some loud noise though. again with the 4-way I have to determine if the location of the 4-way is off or the pin that the valve arm.

I will be in Palm Bay florida this coming up week for my nephews graduation. We are flying out Saturday after I finish grading my class's final project and will be coming back to TN on Thursday

davidwirth · 05-21-2008, 12:08 PM

problem 1-hole where the sear roller sits (the one that was .03 off) has been fixed
Problem 2-It sort of fires but then is slow on the rebound because the valve arm is not pushing the 4-way in
Solution 2- I had a modified valve arm replaced and works fine.
Problem 3- leaking problems but I think the problem with that was the shaft and the cup.
Solution 3- It seems that the material grade I had the seals made from is too hard. Normally, when fired the seal will seat because the pressure forces the seat into the seal. No matter how much I fire, the seat will not seal in the cup. Checking the seal afterwards, there was no indention. If anyone has the grade for the poly that is used in cupseals, it would be great if you could pass that on.

Remember, I will be in Florida from the 24th to the 29th over in Palm Bay

05-17-2008, 10:17 PM	#22 (permalink)
davidwirth call me H8 for short Join Date: Apr 2006 Location: Smyrna TN Posts: 891	I have the sample put together. The trigger pieces all click so it sounds good. I am really really scared to gas it up. __________________ Just call me H8 for short!

05-20-2008, 07:32 PM	#29 (permalink)
davidwirth call me H8 for short Join Date: Apr 2006 Location: Smyrna TN Posts: 891	Yeah, still got a problem with hole location the hole where the sear roller sits (the one that was .03 off) has been fixed. It sort of fires but then is slow on the rebound because the valve arm is not pushing the 4-way in. Also there was some leaking problems but I think the problem with that was the shaft and the cup. The shaft was backing out of the cup causing the hammer to push against it. For some reason the loc-tite never set. So I have reloctited it and will try again. It did make some loud noise though. again with the 4-way I have to determine if the location of the 4-way is off or the pin that the valve arm. I will be in Palm Bay florida this coming up week for my nephews graduation. We are flying out Saturday after I finish grading my class's final project and will be coming back to TN on Thursday __________________ Just call me H8 for short!

05-21-2008, 12:08 PM	#30 (permalink)
davidwirth call me H8 for short Join Date: Apr 2006 Location: Smyrna TN Posts: 891	problem 1-hole where the sear roller sits (the one that was .03 off) has been fixed Problem 2-It sort of fires but then is slow on the rebound because the valve arm is not pushing the 4-way in Solution 2- I had a modified valve arm replaced and works fine. Problem 3- leaking problems but I think the problem with that was the shaft and the cup. Solution 3- It seems that the material grade I had the seals made from is too hard. Normally, when fired the seal will seat because the pressure forces the seat into the seal. No matter how much I fire, the seat will not seal in the cup. Checking the seal afterwards, there was no indention. If anyone has the grade for the poly that is used in cupseals, it would be great if you could pass that on. Remember, I will be in Florida from the 24th to the 29th over in Palm Bay __________________ Just call me H8 for short!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search