mcarterbrown.com  

Electronic If it uses batteries, and fires paintballs... This is the place to sell it.

Reply
 
Thread Tools Search this Thread
Old 11-19-2013, 09:38 AM   #1 (permalink)
Rec Poster
 
Join Date: Dec 2010

Cheap cheap cheap timmies

I have three timmies that need to go, only one of them is totally complete. I wanted to complete these projects but I don't have the time for them. I will say that the membrane pads are a little worn but I have tested them with my spare virtue board and they all worked fine. All these guns will need to be tuned; before I shelved them I did lube them but they have sat and sat because I was looking for very specific parts that never appeared. All the noids I believe work, sold as is...enjoy. I don't want to part these up just yet. Besides the first gun I have not spent too much time on the other two. Post then PM pls. I'm open to trades.

#1 red/blk alias, I have shot this gun and it has no leaks, bounces like crazy.
Very few marks, even the front block is pretty clean, jewels all there.
$220
ups: BL feedneck
CP asa
RL grips (I will part these out)
Hybird adjustment cap
I believe it has the stock trigger, ram and it comes with standard alias bolt
Frenzy board
Stock barrel

The grips screen has been taken out.


#2 blk/blue alias
$190
The first time I tested this marker the lpr was being bypassed, I replaced the square o-ring with a brand new one and that solved that issue but I had no air left to test. This gun will need to be lubed and timed. Nicks here and there but not too bad at all.
If I can find my other bob long assassins barrel it will come with it.

Board: infamous 1.5 board set to 13 bps
upp'd feedneck
Hybird lpr with delrin piston
Hybrid rear adjustment cap
species trigger
comes with standard alias bolt and I believe stock ram
unknown reg-I have rebuilt it



#3 06 timmy. Nothing much to this gun, needs a few things but for the most part its all there. A few nicks along the edges. This gun will need to be lubed.
$170
NDZ feedneck
Board: empire 1.5 12 bps



Last edited by nobouncecap; 11-19-2013 at 10:16 AM.
nobouncecap is offline   Reply With Quote
Old 11-19-2013, 11:21 AM   #2 (permalink)
Rec Poster
 
Join Date: Dec 2010

obo on everything
nobouncecap is offline   Reply With Quote
Old 11-19-2013, 02:03 PM   #3 (permalink)
Active Member
 
abcito's Avatar
 
Join Date: Dec 2008
Location: MA

what things are needed for that 06?
__________________
PBN feedback

MCB Feedback
abcito is offline   Reply With Quote
Old 11-20-2013, 10:09 AM   #4 (permalink)
Rec Poster
 
Join Date: Dec 2010

the only things needed, that I know of, is a reg and either a gauge or a plug screw for the front block.
nobouncecap is offline   Reply With Quote
Old 11-20-2013, 07:33 PM   #5 (permalink)
Rec Poster
 
Join Date: Dec 2010

every thing is gone.
nobouncecap is offline   Reply With Quote
Reply

  mcarterbrown.com » Buy, Sell, Trade » Electronic

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 01:52 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO
© MCB Network LLC