mcarterbrown.com

mcarterbrown.com (http://www.mcarterbrown.com/forums/)
-   Kingman (http://www.mcarterbrown.com/forums/kingman/)
-   -   Hammer7 Side Air -INPUT NEEDED- (http://www.mcarterbrown.com/forums/kingman/222542-hammer7-side-air-input-needed.html)

super_stanchy 01-03-2013 11:43 AM

Hammer7 Side Air -INPUT NEEDED-
 
I have a straight BBA ASA input thread.

Making a 2nd thread for a Phantom Style Side Air Valve.

Choices would be....

Single Port Right
Single Port Left
Dual Side Ports (Left and Right)
Rear
Rear + Side (remote and a gauge perhaps?)

Pricing....
Same Ballpark
$20/$30/$40

More holes=more money (keep that in mind)

Purely Interest.
If I made them, they would be
-Dust Black
-Flush with the back of the frame
-Steel Thread insert for Grip screw
-1/8npt pipe threads in the ports



Stanchy :)

danssoslow 01-03-2013 12:19 PM

This I'd be in on. If you could make one with all three ports, rear, left, and right (makes sense for both sides, just in case plumbing the off side, left or right handed; rear to install a guage) and keep it under/around the $40 range, I'd be all over it.

flyinggobbo 01-03-2013 05:19 PM

I'd buy one with a left side or more port for sure.

Keebler 01-03-2013 05:21 PM

Can you do a bba that also has a port in the side?

pk5 01-03-2013 05:22 PM

What about under? For air through grip.

Keebler 01-03-2013 05:24 PM

I always wanted a false bba. Let me explain. Basically tank goes in the back as always except there no air hole there. The exits out the side into a sideline stab. The than goes from that into another port in the side of the valve

super_stanchy 01-03-2013 05:26 PM

Quote:

Originally Posted by Keebler (Post 2580910)
Can you do a bba that also has a port in the side?

YES

but it would probably be a one off thing....
unless there was enough interest

Quote:

Originally Posted by pk5 (Post 2580911)
What about under? For air through grip.

possibly, but Gas Through usually requires a bunch of other stuff
-Drilling grip frame
-Milling Breech
-Drill/Tap ASA

I could do it, but again it would be a one off kinda thing

flyinggobbo 01-03-2013 05:33 PM

What do you think it'd cost to do an air through grip on one of these? Just an estimate.

super_stanchy 01-03-2013 05:40 PM

Quote:

Originally Posted by flyinggobbo (Post 2580925)
What do you think it'd cost to do an air through grip on one of these? Just an estimate.

I think i charged $125 for a GTG Phantom

and i know them like the back of my hand, im not sure on this one

nerdcore 01-03-2013 07:31 PM

Voted left side only for around $20, and left+rear for about $30.

Reason i chose left side instead of both sides is i'd want to run the line forward & down, then around to the asa (either front fitting or side fitting), like it'd be following a long trigger guard, but don't want the line to interfere with the mag release button, which is on the right hand side.

Rear is just nice if one wanted to run a line similar to a reducer, or put a gauge, although a gauge seems inconsequential unless one were fine-tuning the op. I don't plan on tweaking the internals, outside of running different springs in case the velocity isn't acting right.

Gas-thru-grip is a cool idea, but the amount of work & cost involved makes it impractical for the price point of the pump itself.


All times are GMT -4. The time now is 02:36 PM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO
© MCB Network LLC