mcarterbrown.com

mcarterbrown.com (http://www.mcarterbrown.com/forums/)
-   Kingman (http://www.mcarterbrown.com/forums/kingman/)
-   -   ASA to stock for Back Bottle (http://www.mcarterbrown.com/forums/kingman/224850-asa-stock-back-bottle.html)

Skibbo 01-29-2013 09:13 PM

ASA to stock for Back Bottle
 
I came up with this design to use a CAR stock on my Hammer 7, but it'd work with any marker. It's currently incredibly long, I had to improvise some parts. You would need an air source for the marker to work, I would probably replace the gauge with a 45 elbow and a remote fitting.

Here's what it will look like (shows wrong ID buffer tube, but same idea)
http://i722.photobucket.com/albums/w...psf9c41e91.png

I will drill and tap this for a 1/4-20 thread, but bottomed out so that air will not pass through, and I won't have to worry about thread tape.
http://www.baccipaintball.com/media/...a/i/air859.jpg

Here's the prototype:
http://i722.photobucket.com/albums/w...psc0960221.jpg

It has a 12 gram bucket changer fitting on the front, but a ASA to ASA would also work. It then has a remote line fitting to reduce from ASA to 1/4-20. Not shown is a rod going through the stock, capped off by a washer and cap nut to hold everything tight.

more pictures:
http://i722.photobucket.com/albums/w...ps3276a88b.jpg

cap screw (I broke it by tightening it too much over the sharpened threaded rod...oops)
http://i722.photobucket.com/albums/w...ps06959414.jpg

inner assembly:
http://i722.photobucket.com/albums/w...ps221a1041.jpg

washer caps off each end:
http://i722.photobucket.com/albums/w...ps59edd575.jpg

On the H7:
http://i722.photobucket.com/albums/w...psea676a2c.jpg

paintman161 01-29-2013 09:44 PM

Or you could just use a rap4 air thru stock, but cool setup.

Skibbo 01-29-2013 09:47 PM

Quote:

Originally Posted by paintman161 (Post 2608379)
Or you could just use a rap4 air thru stock, but cool setup.

This cost about $2 to make, so it was much cheaper than the RAP4 ones, even with the cost the dealer I know gets on them.

Skibbo 01-30-2013 08:01 PM

I'm going to head to the local gun store to see if they have any AR buffer tubes in stock. From what I've found they're 1" ID which would fit around a 12 gram adapter and would work pretty nice. I'll see what I can come up with.

Josilk 01-30-2013 08:39 PM

Awesome mod man!!!

this was my solution

http://www.paintballcity.org/images/Josilk/imag0297.jpg

LT.Dan 01-30-2013 08:48 PM

i did somethin similar a while ago on a t9.1
http://i35.photobucket.com/albums/d1...s/DSCF5195.jpg


why not drill and tap on the opposite side of the gauge and install a remote nipple so you dont have the remote line going into your shoulder?

Skibbo 01-30-2013 08:54 PM

Quote:

Originally Posted by LT.Dan (Post 2609452)
i did somethin similar a while ago on a t9.1
http://i35.photobucket.com/albums/d1...s/DSCF5195.jpg


why not drill and tap on the opposite side of the gauge and install a remote nipple so you dont have the remote line going into your shoulder?

The plan is to use 12 grams and an adapter and not a remote. I'd probably just take off the gauge and put on a remote fitting if I went that way.


All times are GMT -4. The time now is 10:39 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC