Buy, Sell, Trade

[Deus Machina]

Alright, I know some of you guys have been asking about these. I had just been waiting until I had turned a whole length of stock into these.

For those unaware, these replace the regulator half of a Classic 'mag valve. Classic valve threads only.

You will need a separate inline regulator. A drop of blue Loctite would be a good idea.

So, let's get started.

The collection.


A stock one for comparison:


1/4" Blind Slot 3 available


1/4 "Torque hole (the flash made it look really rough) sold out, more forthcoming


1/4" Thru slot 1 available


$25 brushed or raw, $30 polished.

I can sell these in blank form (knock off $3, and none ready to go) but you need padded pliers to remove them unless you will be adding some way for a project.
I am doubtful these have enough meat to install a gauge. They may, but I don't want to offer that for sale until I make a personal one and feel comfortable with it in my face.
Available with a blind slot (does not cut through the side edges), through slot (flat-bottomed), or with a hole straight through to stick a hex key through for leverage. Your choice.

3/8" smooth 1 available

$27 brushed or raw, $32 polished.
This one does have the room for a gauge. Add $3 for a gauge hole.
If not gauged, available with blind or through slot, or with pretty much any size leverage hole you want.

1/4" knurled 2 available

$30
Back is raw. Can also be brushed/polished and slotted or holed (add $2) but that defeats the purpose.

5/8" smooth, solid 1 available
(no picture yet!)
$27 brushed or raw, $32 polished.
This was the end of the bar when I didn't have enough for two separate caps. There is room for a gauge (+$3), but would negate the purpose of shortening entirely.
This one is solid, and I don't want to hollow it for fear of marking the outside. Others can be made hollow as a reservoir.
Also in blind or through slots or through-hole, if not gauged.


If I run out of ones read-to-go, I can of course make more. Even specialty ones. They will just take a little longer, even more so after I run out of the material I have on hand.

All prices are shipped, except for you dang foreigners. Canadians add $5, anyone else will have to pay actual shipping but will have the base price adjusted appropriately.

Paypal, money order and checks accepted. I'm not liable for cash, if you try sending that. Trades considered.

Unfortunately, I cannot make these for RT or X-valves until I can get my hands on another one.

Edit: Paypal to MathU41@tampabay.rr.com. PM for other payments or anything custom.

[Darrin79]

Awesome, I want a 1/4'', blind slotted and polished cap. You looking for anything in particular for trades?

[Deus Machina]

Boy, you're quick. Especially for these hours.

I'll hold one for now...

I should have specified. An X- or RT valve would be great, but not expecting that for such simple parts.

A nice mask, marker internals, bodies, brass of pretty much any partially assembled or for-material manner, tools... I'm a tinker, and I get to tinker more than I get to play.

No guarantees I'll take an offer, but I'll hear just about anything!

Edit: I'm also into shooting real firearms and reloading, so associated parts and nicknacks, ammo, and bullets and brass are always welcome.

[Z3R0]

I'll take a smooth 1/4" brushed one, but I'm still deciding on blind slot vs. hole .

EDIT: Alright, make it a smooth 1/4" brushed with a leverage hole .

[ajnin]

I have had one of these for a few years (made by a unknown person). I will have to pick up another. Thanks for making them.

[Murph]

How do you feed air into the marker with one of these things anyway?

[tmoneyblingbling]

Originally Posted by Murph

How do you feed air into the marker with one of these things anyway?

You don't, the air port remains on the front half of the valve assembly.

[tmoneyblingbling]

Knurled 3/8" $32 1 ready to go.
Center bottom. See above. Room for a gauge hole.(+$3)

Will the guage hole come threaded?

[paintballwannab]

What calibers do you load for, I've got a good amount about reloading stuff here can probably come up with a trade idea.

[Deus Machina]

Originally Posted by tmoneyblingbling

Will the guage hole come threaded?

Yes. Standard 1/8 NPT air hole. You couple run a reg or air line, if you really wanted.

Originally Posted by paintballwannab

What calibers do you load for, I've got a good amount about reloading stuff here can probably come up with a trade idea.

9mm, .38 Special, soon 7.62x39 and x54r, and may in the future grab some other common ones.

Also: edited original post to include paypal.