Type R Parts?

LilShank · 12-12-2010, 08:13 PM

Anyone know where I can get a replacement solenoid for my Type R? I'm pretty sure it's blown from over-pressurization.

Thanks!

Rockfrog · 12-12-2010, 10:56 PM

it should be fine with ne o-rings in the noid, it's a very simple design. there should be three (or two, can't rightly remember) o-rings on the solenoid shaft. While the Type-R is a relatively cheaply made marker, the solenoid design is actually quite robust. Have you tried blowing some oil into the LP hose, this was how we used to oil the Type-r and wrath noids back when.

DFSniper · 12-12-2010, 11:01 PM

maybe damon at scenario dreams has a spare T1 noid... that should work.

osCommerce EP Solenoid

Rockfrog · 12-12-2010, 11:12 PM

The T1 used a different type of solenoid (standard 5v humphries, and not the one Damon offers) ... the Type-R uses a noid similar to the diablo wrath marker (9V clapper actuated spring valve)

LilShank · 12-14-2010, 01:08 AM

I managed to get the noid out, and indeed there are supposed to be 3 rings, and one of them was torn to bits. Would O-ring monkey have these in stock or should I look elsewhere?

Rockfrog · 12-14-2010, 01:53 AM

honestly don't know, never had to replace one, sold it before I had any o-ring issues. There was a thread on Peanut Butter that I think had the size. Or, try PM-ing MondMor, Jim might remember the correct size. IIRC they may have been a metric size (which should be able to be had from a hydraulics shop).

these guys might be kind enough to tell you
Welcome!

about all I could find other wise.

LilShank · 12-14-2010, 03:22 AM

Thanks a lot for the help!

Rockfrog · 12-22-2010, 04:18 AM

If you get desperate a standard humphries can be made to fit and will work just as well. just takes some creative fitment. Never did it on my Type-R but I did get my Wrath working on one for a time before ASP started carrying wrath solenoids a while back. They are essentially the same marker (Wrath/Type-R) and some parts can be made to cross fit.

Morhaughn · 04-18-2011, 09:27 AM

I know this is old but I will answer the question. The orings on the type r and other noids of the same type are shocker membrane orings so if you order that kit from oring monkey. You will be set

12-12-2010, 10:56 PM	#2 (permalink)
Rockfrog Seasoned Member Join Date: Feb 2009 Location: Duncan, BC, Canada	it should be fine with ne o-rings in the noid, it's a very simple design. there should be three (or two, can't rightly remember) o-rings on the solenoid shaft. While the Type-R is a relatively cheaply made marker, the solenoid design is actually quite robust. Have you tried blowing some oil into the LP hose, this was how we used to oil the Type-r and wrath noids back when. __________________ Dave G I tinker, therefore I'm broke! Further, now that I've found the MCB BST ... I've recently sold my house and moved under the bridge down the road ... but I've got lots of markers. I have no life, I'm just a dad in constant flux between baby naps and 8yr old tantrums.

12-12-2010, 11:12 PM	#4 (permalink)
Rockfrog Seasoned Member Join Date: Feb 2009 Location: Duncan, BC, Canada	The T1 used a different type of solenoid (standard 5v humphries, and not the one Damon offers) ... the Type-R uses a noid similar to the diablo wrath marker (9V clapper actuated spring valve) __________________ Dave G I tinker, therefore I'm broke! Further, now that I've found the MCB BST ... I've recently sold my house and moved under the bridge down the road ... but I've got lots of markers. I have no life, I'm just a dad in constant flux between baby naps and 8yr old tantrums.

12-14-2010, 01:53 AM	#6 (permalink)
Rockfrog Seasoned Member Join Date: Feb 2009 Location: Duncan, BC, Canada	honestly don't know, never had to replace one, sold it before I had any o-ring issues. There was a thread on Peanut Butter that I think had the size. Or, try PM-ing MondMor, Jim might remember the correct size. IIRC they may have been a metric size (which should be able to be had from a hydraulics shop). these guys might be kind enough to tell you Welcome! about all I could find other wise. __________________ Dave G I tinker, therefore I'm broke! Further, now that I've found the MCB BST ... I've recently sold my house and moved under the bridge down the road ... but I've got lots of markers. I have no life, I'm just a dad in constant flux between baby naps and 8yr old tantrums.

12-22-2010, 04:18 AM	#8 (permalink)
Rockfrog Seasoned Member Join Date: Feb 2009 Location: Duncan, BC, Canada	If you get desperate a standard humphries can be made to fit and will work just as well. just takes some creative fitment. Never did it on my Type-R but I did get my Wrath working on one for a time before ASP started carrying wrath solenoids a while back. They are essentially the same marker (Wrath/Type-R) and some parts can be made to cross fit. __________________ Dave G I tinker, therefore I'm broke! Further, now that I've found the MCB BST ... I've recently sold my house and moved under the bridge down the road ... but I've got lots of markers. I have no life, I'm just a dad in constant flux between baby naps and 8yr old tantrums.

04-18-2011, 09:27 AM	#9 (permalink)
Morhaughn MCB Member Join Date: Sep 2010 Location: Tampa,FL	I know this is old but I will answer the question. The orings on the type r and other noids of the same type are shocker membrane orings so if you order that kit from oring monkey. You will be set __________________ Ninja Dave lever changer ver. 2.0 Playing 2/10 takes balls, but only a few http://210paintball.com/ home of the 2 man 10 ball games MCB Feedback

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search