|
             |
 |
|
| Redux Home of the Redux |
 |
| | LinkBack | Thread Tools | Search this Thread |
10-04-2010, 01:09 PM
| #31 (permalink) | |
| Space Monkey 615 !!!  Join Date: Jun 2008 Location: Middle Tennessee    | Quote:
I quoted above the dump tests I did for the Splatmaster Valves... This coming weekend I will do dump tests on the DuckSlide and Ghost... According to the Data Sheet on the Ultra Copper High Temp RTV the working range is -65* F to 700* F... I also attached the Data Sheet PDF below... http://www.permatex.com/documents/td...tive/81878.pdf I will let you know how it goes and keep you updated  WK2
__________________  Proudly Sponsored by Tippmann, FullClipUSA, Hammerhead, CPX Sports and RANGER UP <--Click the Ranger Up link and receive 20% off your purchase MCB - Feedback for WickedKlown2,,, Automags.Org Online Forums - Feedback for WickedKlown2 | |
|  |
|
10-05-2010, 11:22 PM
| #32 (permalink) | |
| One in the Pipe!  Join Date: Jul 2006 Location: Lubbock TX  |
You know I've gone thru a few seals maybe 4 in the past 2.5 years so although these liquid seals are interesting they seem a bit messy. Last year after going thru several seals at once I ordered 10 from Mike @CCI and haven't needed another since then. Mongo gave me a great tip, lace a fresh seal in with an empty 12gm and seal it for a week. After following his advice I haven't lost another one.
__________________  My Feedback Redux Knowledge Base My Email Line SI Knowledge Base Quote:
| |
|
| |
|
10-05-2010, 11:40 PM
| #33 (permalink) |
| Sneaky Little Bastid #3  Join Date: Apr 2010 Location: Burlington, Massachusetts  |
That soundsx like how I installed my last seal in my gargoyle. Just get a lot of pressure on it with an empty. And let it sit there for a while, heat helps too, I leave mine in front of my laptops exhaust port for 3 hours.
|
|
| |
|
10-11-2010, 12:39 AM
| #34 (permalink) |
| Space Monkey 615 !!! Join Date: Jun 2008 Location: Middle Tennessee |
OK update on the puncture pin seals I did for the Ghost and DuckSlide... I blew one apart and the other is holding up... I think I need to redo both making sure I clean the area with Alcohol before putting the RTV in and get a new tube of Permatex® Ultra Copper High Temp (the old tube I have is 12 years old  )...I will try again in a few weeks... WK2
__________________ Proudly Sponsored by Tippmann, FullClipUSA, Hammerhead, CPX Sports and RANGER UP <--Click the Ranger Up link and receive 20% off your purchase MCB - Feedback for WickedKlown2,,, Automags.Org Online Forums - Feedback for WickedKlown2 |
|
| |
|
10-11-2010, 12:48 AM
| #35 (permalink) | |
| Russel's sweeten it up...  Join Date: Apr 2006 Location: Bean Town, U.S.A. | Quote:
Yea, clean with alcohol first, and a new tube should do it. What's a good curing time for the sealant bro?
__________________ hot links     "Democracy is the worst form of government except for all the others which have been tried." Winston Churchill | |
|
| |
|
10-11-2010, 01:03 AM
| #36 (permalink) |
| Space Monkey 615 !!! Join Date: Jun 2008 Location: Middle Tennessee |
The manufacturer suggests 24 hours,,, on the Splatmasters I let cure for 48 hours... Splatmaster puncture seals are still holding up with no sign of damage or change... Yes a few weeks,,, sorry Brother WK2
__________________ Proudly Sponsored by Tippmann, FullClipUSA, Hammerhead, CPX Sports and RANGER UP <--Click the Ranger Up link and receive 20% off your purchase MCB - Feedback for WickedKlown2,,, Automags.Org Online Forums - Feedback for WickedKlown2 |
|
| |
|
10-12-2010, 07:57 AM
| #37 (permalink) |
| Russel's sweeten it up... Join Date: Apr 2006 Location: Bean Town, U.S.A. |
I do remember reading about some one stamping then out of tire inner tubes.
__________________ hot links "Democracy is the worst form of government except for all the others which have been tried." Winston Churchill |
|
| |
|
11-12-2010, 10:28 PM
| #38 (permalink) | |
| Master Metal Whittler  Join Date: Apr 2008 |
currently using a standard Buna N o-ring in an old BE changer with no problems thus far.
__________________ BSCustoms Design and Fabrication. --------------------------------------- Being copied is the greatest form of flattery. --------------------------------------- FEEDBACK Quote:
| |
|
| |
|
11-13-2010, 11:29 PM
| #39 (permalink) | |
| Idiot Fanboy.  Join Date: Apr 2006 Location: S. NJ  |
my seal was gone in my gun today. stock CCI seal, dropped right in, worked like a charm.
__________________ Generously Sponsored By: Valken|GoG Paintball |ScenarioSuperstore.com|Kohn Sports|Virtue Paintball|FogTech Understood Clothing|OXCC MD Follow us: http://twitter.com/DeltaPaintball "The future is already here - it's just not very evenly distributed." Shadawg's Feedback http://www.mcarterbrown.com/forums/f...tml#post932780 Quote:
| |
|
| |
|
|
| Thread Tools | Search this Thread |
|
|
