mcarterbrown.com  

Showing results 1 to 12 of 12
Search took 0.01 seconds.
Search: Posts Made By: Eskie
Forum: Kingman 03-12-2013, 10:45 AM
Replies: 12
Views: 1,003
Posted By Eskie
I thought a force feeding system usually solves...

I thought a force feeding system usually solves the chopping issue?

In any case, I've been thinking about it. It could be as simple as an LED, photodiode, and a transistor switch wired between the...
Forum: Kingman 03-12-2013, 07:56 AM
Replies: 4
Views: 362
Posted By Eskie
Thanks, spring replacement it is then.

Thanks, spring replacement it is then.
Forum: Kingman 03-09-2013, 09:44 AM
Replies: 4
Views: 362
Posted By Eskie
MR5 velocity adjustment

The new field I'm playing at has a speed limit of 230 fps. However my MR5 is shooting at least 250fps with the velocity adjustment screw backed all the way out. Is there anything I could do to...
Forum: Kingman 03-08-2013, 11:32 AM
Replies: 7
Views: 305
Posted By Eskie
Browse through here...

Browse through here (http://dx.com/c/hobbies-toys-899/airsoft-guns-supplies-837/gun-mounts-rails-876) and pick whatever you fancy.
Forum: Kingman 03-08-2013, 11:11 AM
Replies: 7
Views: 305
Posted By Eskie
If not being able to see down the sight is your...

If not being able to see down the sight is your only problem then also consider buying some rail raisers to elevate the sights instead.
Forum: Kingman 03-07-2013, 11:19 PM
Replies: 18
Views: 1,930
Posted By Eskie
Take a look at the bottom line kits on this page...

Take a look at the bottom line kits on this page (http://www.pinnaclepaintballsupply.com/trracer_acc.html). All of them should fit the hammer 7 as well.
Forum: Kingman 03-07-2013, 11:18 PM
Replies: 7
Views: 305
Posted By Eskie
Spyder makes a Feed neck cover plate...

Spyder makes a Feed neck cover plate (http://www.paintballgear.ca/product/Spyder_MRX_Feedneck_Cover_Plate.html). It's for the MRX but it fits.

You might have to machine something to cover the...
Forum: Kingman 03-06-2013, 10:45 PM
Replies: 43
Views: 3,905
Posted By Eskie
Inspired by the designs in this thread, I've...

Inspired by the designs in this thread, I've decided to try my own hand at it too.

http://i.imgur.com/MXLOiTT.jpg
Forum: Kingman 02-27-2013, 02:33 PM
Replies: 36
Views: 2,174
Posted By Eskie
Only a few hundred shots so far, but so far so...

Only a few hundred shots so far, but so far so good.
Forum: Kingman 02-27-2013, 11:16 AM
Replies: 4
Views: 539
Posted By Eskie
The first few times were really tight. I noticed...

The first few times were really tight. I noticed that the magazines weren't going in smoothly until the sharp angles on the top steps of the magazine were worn smooth a little.

The angle of...
Forum: Kingman 02-27-2013, 08:32 AM
Replies: 36
Views: 2,174
Posted By Eskie
I double-sided taped a small piece of foam on the...

I double-sided taped a small piece of foam on the back of the detent, which made it a lot stiffer when the barrel was inserted. I'm sure this causes a lot more wear on the detent but double feeding...
Forum: Kingman 02-27-2013, 08:25 AM
Replies: 4
Views: 539
Posted By Eskie
It just needs to be broken in. I spent 5 minutes...

It just needs to be broken in. I spent 5 minutes just inserting each magazine and pulling it out, now it's all silky smooth.
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT -4. The time now is 10:00 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC