mcarterbrown.com  

Showing results 1 to 10 of 10
Search took 0.00 seconds.
Search: Posts Made By: cntrmass
Forum: Ask The Experts 07-22-2009, 07:56 AM
Replies: 18
Views: 538
Posted By cntrmass
Well, not in this case. The ASA air-through hole...

Well, not in this case. The ASA air-through hole is not located where the spring is inserted but through a hole on the outside right of the ASA where a fitting is attached on outside of marker that...
Forum: Ask The Experts 07-19-2009, 06:31 PM
Replies: 18
Views: 538
Posted By cntrmass
Well, shimming the spring didnt seem to make any...

Well, shimming the spring didnt seem to make any difference, if anything it appears to have lowered the velocity. Guess I'll see if I can find a spring kit and/or replace with a comparable spring....
Forum: Ask The Experts 07-15-2009, 10:10 AM
Replies: 18
Views: 538
Posted By cntrmass
Sounds good. Thanks everyone for your input on...

Sounds good. Thanks everyone for your input on this. I think I'll start by just trying to shim the spring enough to get my velocity close to 270 fps. Im sure if I just used co2 instead of air I would...
Forum: Ask The Experts 07-14-2009, 09:36 PM
Replies: 18
Views: 538
Posted By cntrmass
where would the shims go, in front of the spring...

where would the shims go, in front of the spring or back near asa, or doesnt it matter?
So Im guessing tighter spring means higher velocity in tis case.
Forum: Ask The Experts 07-14-2009, 09:23 PM
Replies: 18
Views: 538
Posted By cntrmass
pics

Here are some pics I promised.
There isnt anything inside the bolt that can be adjusted, pretty much just hollowed out. Is there anywhere else you can see in these pics where I might be able to...
Forum: Ask The Experts 07-14-2009, 02:54 PM
Replies: 18
Views: 538
Posted By cntrmass
I'll get some pics up either tonight or tomorrow....

I'll get some pics up either tonight or tomorrow. I'll try and break it down tonight and get pics for each piece, bolt, spring, etc... then you guys can tell me if its possible to do anything with...
Forum: Ask The Experts 07-14-2009, 11:27 AM
Replies: 18
Views: 538
Posted By cntrmass
No problem - I'll get some nice pics for ya. ...

No problem - I'll get some nice pics for ya. :bang: (Bobby Dukes) :D
Its a nice old gun. My son found it about 5 years ago in our basement when he was 10 so I gave him some paintball history and...
Forum: Ask The Experts 07-14-2009, 10:57 AM
Replies: 18
Views: 538
Posted By cntrmass
Thanks for the info Surestick and Ironexpress. Im...

Thanks for the info Surestick and Ironexpress. Im at work and dont have the marker with me but as soon as I get home I'll begin the process then post my findings.

Thanks again
Joe
Forum: Ask The Experts 07-14-2009, 09:56 AM
Replies: 18
Views: 538
Posted By cntrmass
ok - I've never taken this thing apart so guess I...

ok - I've never taken this thing apart so guess I should learn now. Everything on this marker is stock.



I assume I need to take the bolt out to verify this?
There is a small nob at the end...
Forum: Ask The Experts 07-14-2009, 09:05 AM
Replies: 18
Views: 538
Posted By cntrmass
Sheridan produced PMI II question

I apologize in advance if this question has already been answered.

I have an old PMI II (constant air setup) that I dug out of the closet and want to start using it again but have a question.
...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -4. The time now is 11:29 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC