It is a PGP .... REALLY ! - Page 2

DCB · 08-10-2007, 06:26 PM

Very nice indeed!!!

Motorhead · 08-17-2007, 09:20 PM

Update ....

After some chronograph time, seems the little Sheridan does NOT want to be regulated, even at 700#'s velocity would not go above 260.

So with a tad bit of valve tweaking and now set up bottom lined to a direct connect ASA, she is shooting 280 without breaking a sweat, while holding +/- 6-8 fps in the process ..... Sweet !

splattttttt · 09-22-2007, 08:56 PM

Which valve, the cartridge?
What did you end up doing to it?
Nice job on the frame BTW

Motorhead · 09-27-2007, 09:05 PM

I replaced the piercer / valve with a PPS Dyna style. Opened up the male threaded portion on valve body half so the gas behind cup seal could flow out around it when fully compressed. Put an @ .030" flat along one side of pierce pin so a tad more flow will enter valve during fire sequence. Opened vent hole in valve body with a #3 drill.

Scott

Cunha · 09-27-2007, 09:09 PM

Need the large air passageway..

That gun doesnt explode paint? Thatd be rare if it didnt with the stock bolt.

The blazer frame is nice. It would be cheaper to put an automag frame on one of those though.

Motorhead · 09-27-2007, 09:16 PM

Ah, funny you mention exploding paint

Did a stock bolt mod that has a push pin in face of bolt. When bolt slides into "Lock" position a flat pin bumps the ball forward @ 3/16". Also added 2 wedgets either side to stop roll outs.
Gun Does NOT break paint at all now

splattttttt · 09-27-2007, 11:12 PM

You know? I've never broke paint with a PGP. And they were mostly stock. Some had more kick then other's, but never broke paint.
I spring them to shoot below 275fps on the first shot.
I know that they are a close range marker, and anything above that is useless.

Motorhead · 09-28-2007, 02:05 AM

Can't honestly say this PGP is a close in Gun

granted sighting plane is a tad short, but as for accuracy at 280 fps, it is damn near as accurate as either of my Blazers

It has accuracy that is more than enough to even play woods ball with IMO.

I love this little pistol

08-10-2007, 06:26 PM	#11 (permalink)
DCB Pumper Join Date: Apr 2006 Location: Jax, FL	Very nice indeed!!! __________________ DCB<>< John 14:6 CPPA #1092 Pump Gun Pimp #80 LPPC #164 Feedback http://www.mcarterbrown.com/forums/f...html#post78710 Gallery http://www.mcarterbrown.com/gallery/...er=184&cat=500

08-17-2007, 09:20 PM	#12 (permalink)
Motorhead Seasoned Member Join Date: Jun 2007 Location: Northern California U.S.A.	Update .... After some chronograph time, seems the little Sheridan does NOT want to be regulated, even at 700#'s velocity would not go above 260. So with a tad bit of valve tweaking and now set up bottom lined to a direct connect ASA, she is shooting 280 without breaking a sweat, while holding +/- 6-8 fps in the process ..... Sweet ! __________________ Older & Slower ... But well armed. Motorheads feedback Last edited by Motorhead; 08-18-2007 at 12:59 AM..

09-22-2007, 08:56 PM	#13 (permalink)
splattttttt MCB Member Join Date: Apr 2006 Location: Bean Town, U.S.A.	Which valve, the cartridge? What did you end up doing to it? Nice job on the frame BTW __________________ My Feed Back and album Norman Vincent Peale: "Believe that you are defeated, believe it long enough, and it is likely to become a fact. We tend to get what we expect." Don't let the so called Global Elite stick you with a chip. FIGHT FOR FREEDOM Carpe Diem, and smile a little Whish your Dog was smarter???

09-27-2007, 09:05 PM	#14 (permalink)
Motorhead Seasoned Member Join Date: Jun 2007 Location: Northern California U.S.A.	I replaced the piercer / valve with a PPS Dyna style. Opened up the male threaded portion on valve body half so the gas behind cup seal could flow out around it when fully compressed. Put an @ .030" flat along one side of pierce pin so a tad more flow will enter valve during fire sequence. Opened vent hole in valve body with a #3 drill. Scott __________________ Older & Slower ... But well armed. Motorheads feedback

09-27-2007, 09:16 PM	#16 (permalink)
Motorhead Seasoned Member Join Date: Jun 2007 Location: Northern California U.S.A.	Ah, funny you mention exploding paint Did a stock bolt mod that has a push pin in face of bolt. When bolt slides into "Lock" position a flat pin bumps the ball forward @ 3/16". Also added 2 wedgets either side to stop roll outs. Gun Does NOT break paint at all now __________________ Older & Slower ... But well armed. Motorheads feedback

09-27-2007, 09:09 PM	#15 (permalink)
Cunha MCB Member Join Date: Apr 2006 Location: Monterey, CA	Need the large air passageway.. That gun doesnt explode paint? Thatd be rare if it didnt with the stock bolt. The blazer frame is nice. It would be cheaper to put an automag frame on one of those though.

09-27-2007, 11:12 PM	#17 (permalink)
splattttttt MCB Member Join Date: Apr 2006 Location: Bean Town, U.S.A.	You know? I've never broke paint with a PGP. And they were mostly stock. Some had more kick then other's, but never broke paint. I spring them to shoot below 275fps on the first shot. I know that they are a close range marker, and anything above that is useless. __________________ My Feed Back and album Norman Vincent Peale: "Believe that you are defeated, believe it long enough, and it is likely to become a fact. We tend to get what we expect." Don't let the so called Global Elite stick you with a chip. FIGHT FOR FREEDOM Carpe Diem, and smile a little Whish your Dog was smarter???

09-28-2007, 02:05 AM	#18 (permalink)
Motorhead Seasoned Member Join Date: Jun 2007 Location: Northern California U.S.A.	Can't honestly say this PGP is a close in Gun granted sighting plane is a tad short, but as for accuracy at 280 fps, it is damn near as accurate as either of my Blazers It has accuracy that is more than enough to even play woods ball with IMO. I love this little pistol __________________ Older & Slower ... But well armed. Motorheads feedback

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search