mcarterbrown.com  

Reply
 
Thread Tools Search this Thread
Old 02-19-2014, 08:39 PM   #1 (permalink)
Lovesolderguns
 
Lovemesomepumps's Avatar
 
Join Date: Feb 2014

SMG 60 help

Hey guys, Just got my smg 60 in ,however when I gas it up with HPA (my anti siphon tank is coming in but I dont have it now) the gun leaks. Now I'm trying to disassemble the gun ,but I dont know how. If anyone knows let me know.
Lovemesomepumps is offline   Reply With Quote
Old 02-19-2014, 09:30 PM   #2 (permalink)
Original SWARM
 
Smiley's Avatar
 
Join Date: Oct 2007

Leaks where ?
does it have an internal air line or a hardline on the left side ?
Smiley is offline   Reply With Quote
Old 02-19-2014, 09:40 PM   #3 (permalink)
Lovesolderguns
 
Lovemesomepumps's Avatar
 
Join Date: Feb 2014

Internal gasline. I believe the leak is coming from the internal gasline/ the bolt because when I air it up with HPA. Could it be that im not using a anti siphon co2 tank ?
Lovemesomepumps is offline   Reply With Quote
Old 02-19-2014, 10:30 PM   #4 (permalink)
Thrill Me!
 
snaparen's Avatar
 
Join Date: Jun 2008
Location: looking through the knotholes in granny's wooden leg

You want a siphon tank for these, not a anti-siphon.
If the leak is in the line it does not matter what type of air you use, it will leak.

Check the air line fitting at the valve, this is a very common place for the internal air line to leak, due to valve movement.
__________________
4 out of 5 voices in my head say i'm ok
Quote:
Originally Posted by Mar View Post
the mods here suck...
Quote:
Originally Posted by MaD View Post
Asking for brass on MCB is like going to the grocery and saying "Looking for food, you guys have any"?
My Feedback

Stuff I want or need evenually

want to buy red pump handle

Nelson, Tippmann, Dye, Angle, Spyder stuff
snaparen is offline   Reply With Quote
Old 02-19-2014, 10:32 PM   #5 (permalink)
Post Whore
 
big jim's Avatar
 
Join Date: Sep 2006
Location: Holdrege Nebraska

First, get that term ANTI out of your head! What you need is a siphon tank. This baby runs on pure liquid!

There should be a set screw in the top of the rear sight. First loosen the set screw. Next there is a large plug in line with the bolt and hammer on the very rear of the gun. This plug unscrews, but it has the main drive spring and spring pin set in the pocket on the front side so be ready for it to pop out when the plug is finally unscrewed. With the plug out and the spring and pin removed the bolt will slide all the way back and allow the cocking bolt to pull out the side through the larger hole in the cocking slot. Next the hammer should slide right out. Now you should be able to air it up and find where the air is leaking out of.
__________________
Big Jim

Quote:
Originally Posted by Mr. Furious View Post
You'll have a tough time finding a nicer group of people on the internet(even if our opinions all suck).

Quote:
Originally Posted by Vitalsilence View Post
I've dealt with canadians several times and I usually undercharge by 2-5 dollars cause I feel bad for them sometimes. Just my 2cents.

feedback http://www.mcarterbrown.com/forums/f...k-big-jim.html
big jim is offline   Reply With Quote
Old 02-19-2014, 10:35 PM   #6 (permalink)
Post Whore
 
big jim's Avatar
 
Join Date: Sep 2006
Location: Holdrege Nebraska

Snaparen is right. there is a screw in the rear ASA that works to depress the bottle pin.that screw takes a flat head screw driver. First try tightening it. That may solve your problem.
__________________
Big Jim

Quote:
Originally Posted by Mr. Furious View Post
You'll have a tough time finding a nicer group of people on the internet(even if our opinions all suck).

Quote:
Originally Posted by Vitalsilence View Post
I've dealt with canadians several times and I usually undercharge by 2-5 dollars cause I feel bad for them sometimes. Just my 2cents.

feedback http://www.mcarterbrown.com/forums/f...k-big-jim.html
big jim is offline   Reply With Quote
Old 02-19-2014, 11:06 PM   #7 (permalink)
Lovesolderguns
 
Lovemesomepumps's Avatar
 
Join Date: Feb 2014

I tried to tighten it ,but it was all the way in. It still leaks ,but when I opened it I noticed that there is no actual rubber tubing/pipping. imgur: the simple image sharer as you can see I dont notice tubing for the gas to go through.
Lovemesomepumps is offline   Reply With Quote
Old 02-19-2014, 11:13 PM   #8 (permalink)
Original SWARM
 
Smiley's Avatar
 
Join Date: Oct 2007

looks like you are missing the internal line, an O-ring on the valve and the washer that goes in front of the valve flange.
Bacci has the washers and maybe the line or try PB Sports in INDIANA.
the oring for an A5 hammer should work.
Smiley is offline   Reply With Quote
Old 02-19-2014, 11:49 PM   #9 (permalink)
Lovesolderguns
 
Lovemesomepumps's Avatar
 
Join Date: Feb 2014

THANK YOU SO MUCH!!!! Also, should their be a o-ring on the hammer at the very tip ?
Lovemesomepumps is offline   Reply With Quote
Old 02-19-2014, 11:53 PM   #10 (permalink)
Lovesolderguns
 
Lovemesomepumps's Avatar
 
Join Date: Feb 2014

Just checked with Bacci's web store. No gas line. T_T any advice on where I can grab one ?
Lovemesomepumps is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » Tippmann

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 12:21 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC