|
             |
 |
|
| Tribals Tribal fan? Then this is the forum for you! |
 |
| | LinkBack | Thread Tools | Search this Thread |
04-08-2007, 12:41 PM
| #1 (permalink) | |
| MCB Member  Join Date: Nov 2006
Posts: 346
| General Tech help.............. Pic fully disassembled  Adjusting the AOC..... How to change the AOC. First take off the aoc cap. Next remove the asa via the asa screw. Remove the plunger along with the spring and the aoc. There might be a set screw on the side body of the aoc. If so loosen it. This in turn will loosen the aoc screw. Turn the screw in to increase the persure, out to decrease the persure. Return the aoc/spring/plunger and screw in the asa. YOU WILL NEED A GAUGE! to do it right. The perfect pressure is around 95-105. Once you get that pressure, remove the aoc again, put loctite on the set screw, let dry and replace it into the body. From left to right: front cap, AOC plunger, AOC spring, AOC body, valve spring, cup seal and stem, valve and valve dampner.  Just the AOC  Tribal schematic........... Here is a link to the Tribal V1E Stock Boardset. Tribal manual.......... http://www.tribal-paintball.com/trib...ibalmanual.pdf Tribal basics ...... if you have the time to just sit and check it out. http://www.tribal-paintball.com/trib...ibalbasics.pdf
__________________ my feedback thread........ http://www.mcarterbrown.com/forums/s...ead.php?t=9789 Quote:
Last edited by shifty; 04-08-2007 at 12:46 PM. | |
|  |
|
04-08-2007, 08:18 PM
| #3 (permalink) | |
| MCB Member Join Date: Nov 2006
Posts: 346
| Nope...... Rich took pics of his a long time ago. You ever get the need to get rid of yours , yoiu know where I'm at.
__________________ my feedback thread........ http://www.mcarterbrown.com/forums/s...ead.php?t=9789 Quote:
| |
|
| |
|
04-09-2007, 11:10 AM
| #4 (permalink) |
| Pumpers use both hands.  Join Date: Aug 2006 Location: Nicholasville, KY
Posts: 646
| Don't see that happening. I got a lpc/reg combo, a ccm feedneck, and a ram spring, from edwin for her. I might eventually swap out for a chaos board with break beams but, not unless I can figure a good way to do it without screwing with the overall appearance.
__________________ Knowledge is the only good and ignorance the only evil. |
|
| |
|
04-09-2007, 04:22 PM
| #5 (permalink) |
| Active Member  Join Date: Aug 2006 Location: Kansas City, MO
Posts: 285
| What, you went back to the land of the evil centerfeeds? *tsk* For shame... =D How ya been, Medic?
__________________ WWVD? Sometimes, you just have to ask yourself, "What would Velcor do?" My Feedback TOG |
|
| |
|
04-09-2007, 06:01 PM
| #6 (permalink) | ||
| MCB Member Join Date: Nov 2006
Posts: 346
| Quote:
 
__________________ my feedback thread........ http://www.mcarterbrown.com/forums/s...ead.php?t=9789 Quote:
| ||
|
| |
|
04-14-2007, 12:29 PM
| #7 (permalink) |
| Pumpers use both hands. Join Date: Aug 2006 Location: Nicholasville, KY
Posts: 646
| Yeah. I have been converted. Sort of by getting myself conned into tournament play again and for various other reasons. I still prefer rf setupd but I find that switching back and forth was really screwing with me and since it is hard to find a good rf electro I went back to centerfeeds. Besides how could I pass up a deal on a stock adicted 2.2 for >$400. I've wanted an addicted for quite some time. From there it just snowballed. Now I have 3 electros AGAIN, 3 mechs and 3 pumps that travel with me everywhere just in case. All of them cf.
__________________ Knowledge is the only good and ignorance the only evil. |
|
| |
|
|
| Thread Tools | Search this Thread |
|
|
