mcarterbrown.com
 

Reply
 
Thread Tools Search this Thread
Old 01-20-2013, 03:50 PM   #1 (permalink)
Newbie
 
Join Date: Dec 2012
Location: socal

Mq2 karnivor help

I just installed a mq2 valve in my karni and used it yesterday playing. It shot perfectly fine except that the fps is low on it and can't get it any higher. I have the little plastics white shim out and have the hpr at 290 psi "highest it will go before leaking"
I'm totally out of ideas. Please help
facelesskillah is offline   Reply With Quote
Old 01-20-2013, 05:07 PM   #2 (permalink)
Newbie
 
Join Date: Jun 2012

what's your son?
t0wer is offline   Reply With Quote
Old 01-20-2013, 05:41 PM   #3 (permalink)
Newbie
 
Join Date: Dec 2012
Location: socal

It's at 4 right now
facelesskillah is offline   Reply With Quote
Old 01-21-2013, 01:40 AM   #4 (permalink)
Newbie
 
Join Date: Jun 2012

Try increasing son to 5ms.
t0wer is offline   Reply With Quote
Old 01-21-2013, 10:38 AM   #5 (permalink)
Newbie
 
Join Date: Dec 2012
Location: socal

Ok will try that. I have an idea what that will so. But could you still tell me what it will so so I can be sure..
facelesskillah is offline   Reply With Quote
Old 01-22-2013, 09:31 PM   #6 (permalink)
Newbie
 
Join Date: Jun 2012

it will keep the valve open a little longer increasing fps
t0wer is offline   Reply With Quote
Old 01-23-2013, 12:28 AM   #7 (permalink)
Rec Poster
 
All-Star Reject's Avatar
 
Join Date: Jun 2010

CCM Fan
Sounds like your valve is sticking, what kind of lube did you use. Most everyone including myself has the best luck with dow 33. It is not real necessary to polish the inside of the brass housing but it can help or relube or change the oring on the poppet (not the poppet face seal unless it is leaking).
All-Star Reject is offline   Reply With Quote
Old 01-23-2013, 05:49 PM   #8 (permalink)
Newbie
 
Join Date: Dec 2012
Location: socal

I used the Dow 33 from eclipse. And yup that's what I thought it will do thx
facelesskillah is offline   Reply With Quote
Old 01-31-2013, 05:14 PM   #9 (permalink)
Newbie
 
Join Date: Dec 2012
Location: socal

Crap so my e2 board only goes up to 4ms on the "son.." is their any other tricks I can do to raise the fps?

Last edited by facelesskillah; 01-31-2013 at 05:48 PM.
facelesskillah is offline   Reply With Quote
Old 02-01-2013, 07:26 AM   #10 (permalink)
Rec Poster
 
All-Star Reject's Avatar
 
Join Date: Jun 2010

CCM Fan
Check that you don't have the screw that holds the poppet seal in too tight. It can cause the seal to spread out too much and cause it to drag. If you take it off make sure you use a drop of blue locktite when you screw it back on or it will come loose over time.
All-Star Reject is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » WGP

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 01:06 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC