mcarterbrown.com
 

Reply
 
Thread Tools Search this Thread
Old 03-07-2013, 12:25 AM   #1 (permalink)
chuff chuff
 
Hobbes's Avatar
 
Join Date: Apr 2006
Location: Hudson, NH
Send a message via AIM to Hobbes

Kapp vertical ASA oring

Anyone know the size of the oring needed for a Kapp vertical ASA?

Thanks
Hobbes is offline   Reply With Quote
Old 03-08-2013, 12:13 PM   #2 (permalink)
MCB Member
 
Riddler's Avatar
 
Join Date: Apr 2006
Location: pgh, pa

CCM Fan
Not off the top of my head, but i've replaced one before, and it's a completely standard, common size, despite the odd oval groove and how mangled a dried up, old one may look when you remove it.
Riddler is offline   Reply With Quote
Old 03-08-2013, 08:08 PM   #3 (permalink)
Active Member
 
addicted2dunes's Avatar
 
Join Date: May 2012
Location: Orcutt, CA

-113 is the size.....
__________________
ATOMIC FABRICATION
PM me about Autococker machining!
addicted2dunes is offline   Reply With Quote
Old 03-09-2013, 06:28 PM   #4 (permalink)
chuff chuff
 
Hobbes's Avatar
 
Join Date: Apr 2006
Location: Hudson, NH
Send a message via AIM to Hobbes

I looked up the 113 orings but they look too small. I measured the diameter of the hole with calipers and it read 0.89", so I think that works out to a 117.

Last edited by Hobbes; 03-09-2013 at 06:42 PM.
Hobbes is offline   Reply With Quote
Old 03-09-2013, 07:12 PM   #5 (permalink)
Active Member
 
addicted2dunes's Avatar
 
Join Date: May 2012
Location: Orcutt, CA

-117 is huge! That's the size you use for WGP feednecks to give you a reference.
__________________
ATOMIC FABRICATION
PM me about Autococker machining!
addicted2dunes is offline   Reply With Quote
Old 03-09-2013, 07:12 PM   #6 (permalink)
Active Member
 
addicted2dunes's Avatar
 
Join Date: May 2012
Location: Orcutt, CA

-113 is 2K
-115 is pre-2K
__________________
ATOMIC FABRICATION
PM me about Autococker machining!
addicted2dunes is offline   Reply With Quote
Old 03-09-2013, 09:42 PM   #7 (permalink)
Active Member
 
addicted2dunes's Avatar
 
Join Date: May 2012
Location: Orcutt, CA

-115 is:
ID: 11/16" 0.674"
OD: 7/8" 0.880"
__________________
ATOMIC FABRICATION
PM me about Autococker machining!
addicted2dunes is offline   Reply With Quote
Old 03-18-2013, 05:13 PM   #8 (permalink)
chuff chuff
 
Hobbes's Avatar
 
Join Date: Apr 2006
Location: Hudson, NH
Send a message via AIM to Hobbes

The oring from an Intimidator feedneck fits in the ASA, it's just too thin. The manual doesn't say how big the feedneck oring is though.

Last edited by Hobbes; 03-18-2013 at 05:17 PM.
Hobbes is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » WGP

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 10:07 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC