mcarterbrown.com  

Reply
 
Thread Tools Search this Thread
Old 04-10-2013, 06:37 PM   #1 (permalink)
------------
 
boltaction's Avatar
 
Join Date: Jun 2011
Location: Derry, NH

CCM Fan
Worrframe issue...

Hey fellas.

I picked up and 05 prostock with the worr-frame and the connectors for the battery seem to have detached themselves from the board. do these have to be soldered back in place or what? I can get pics in a minute.

Previous to this happening, the battery was held in very loosely and the gun would only stay on if I held it upsidedown.


IMG_1009 by Boltaxtion, on Flickr

Last edited by boltaction; 04-10-2013 at 07:13 PM.
boltaction is offline   Reply With Quote
Old 04-10-2013, 07:24 PM   #2 (permalink)
------------
 
boltaction's Avatar
 
Join Date: Jun 2011
Location: Derry, NH

CCM Fan
Update and a bit more info.

If I hold a 9volt up to the connectors on the board it turns on. But now I have another issue. Airs up fine, solenoid clicks but then all I'm getting is a second "click" form the 3 way. no shooting.

Its really a bit odd. When I first got the gun I noticed the slightly dodgy connectors but it aired up and dryfired fine (fast too =). But when I tried to put paint through it, it would cycle just barely. It would load a ball and the next ball would just push that ball into the barrel. So i thought velocity was low. turned it up 1 turn and reassembled. I got a few more barely cycling low pressure shots before the battery issues arose.

Any help'd be great.

Tank output is 850 is that is relavent. roughly 3000 psi in it.
boltaction is offline   Reply With Quote
Old 04-10-2013, 10:25 PM   #3 (permalink)
------------
 
boltaction's Avatar
 
Join Date: Jun 2011
Location: Derry, NH

CCM Fan
Well I guess the second "click" is from the 3-way solenoid up front? It's a bone stock setup. Picture below.

I don't want to mess with the LPR but I think It must be down to a pressure/timing issue now that it won't cycle. Unless someone thinks it's bad electronics. I dialed the velocity back to where it was originally and had the same result.


IMG_1010 by Boltaxtion, on Flickr
boltaction is offline   Reply With Quote
Old 04-13-2013, 03:55 PM   #4 (permalink)
Newbie
 
Join Date: Jun 2012

sounds like the lpr is shut off.

and you should be able buy a new board on pbgateway for around $30
or solder the battery contacts back on.
t0wer is offline   Reply With Quote
Old 04-13-2013, 05:52 PM   #5 (permalink)
------------
 
boltaction's Avatar
 
Join Date: Jun 2011
Location: Derry, NH

CCM Fan
Yea I turned up the LPR a tad and it's shooting fine now.

Dammit. I have'nt soldered since high school.

Thanks for the tips.
boltaction is offline   Reply With Quote
Old 04-13-2013, 07:02 PM   #6 (permalink)
Un-Active Member
 
SEFishy's Avatar
 
Join Date: Jan 2007
Location: El Paso

Brass N Wood Fan
Palmers Fan
The first thing I always do is set the gun to its factory fast settings. Turn the eyes off and lpr all the way off. Turn it in a half turn as you attempt to shoot it. Once it fires smoothly turn it 1/4 turn farther. At this point I sharpie a mark on the lpr to ensure the screw is not creeping.

As for soldering its real easy as the contacts are rather large. I don't for see you having any issues here
__________________
WTB - Cocker, Mag, Phantom, QLoader Parts

For Sale


Hawkeye20: "......Hit!..............medic..... oh God...."
pghp8ntballer: "Cause you know, first strike and flatline systems together with a scope allow you to shoot into the future."
SEFishy is offline   Reply With Quote
Old 05-03-2013, 02:25 AM   #7 (permalink)
Furries are EVERYWHERE :3
 
Stripes's Avatar
 
Join Date: Dec 2007
Location: Palatine IL

Don't solder the battery contacts back on
Make a stop at your local electronics store and get a 9v harness, and solder tha on
That way you don't have to worry about the pressure against the contacts, or little variations in battery length, just clip it to the top
It's what I did with my select fire frame

Also, if you want to use the fire modes, and don't have a jumper, you can use a 2 pin jumper off a hard drive or cd drive
__________________
Quote:
I love sucking the juice out of pickles. -slowerpig81
Stripes is offline   Reply With Quote
Old 05-03-2013, 07:29 PM   #8 (permalink)
MCD Member
 
FrankW's Avatar
 
Join Date: Mar 2012
Location: So Cal (OC)

I completely agree on getting a 9v harness in there. I picked one up from Radio Shack and soldered it in there. I've never soldered in my life, but it still wasn't too bad. Only barely burned myself...
__________________
Feedback
FrankW is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » WGP

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 10:42 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC