mcarterbrown.com  

Reply
 
Thread Tools Search this Thread
Old 06-16-2013, 02:16 PM   #1 (permalink)
Newbie
 
TimberlineShooter's Avatar
 
Join Date: Jun 2013

Post Auto Cocker Orracle

Needing some advice on working on a old school autococker, my brother a few years back got a orracle and we've been working our butts off the last few months to get it working again.
Here's what we've done so far
Replaced the orings in the low pressure and three way
Replaced the whole ram pistion
The main reg is tuned to 260 psi

The gun still seems to be leaking from the low pressure valve
And the gun doesn't want to shoot right
And as this gun is a gorgeous collectible we want to get it working
Any hints would be great and help full
TimberlineShooter is offline   Reply With Quote
Old 06-16-2013, 02:21 PM   #2 (permalink)
Dr. says it will clear up
 
leathalh's Avatar
 
Join Date: Jun 2011
Location: Denver, Co

CCM Fan
Where is it leaking from, soapy water and a spray bottle is great to find those leaks. If it is leaking down the barrel check the valve cup seal. You will need a valve removal tool.
__________________
Autocockers are not more accurate, I'm just more accurate when I shoot autocockers.
leathalh is online now   Reply With Quote
Old 06-17-2013, 07:13 PM   #3 (permalink)
Newbie
 
TimberlineShooter's Avatar
 
Join Date: Jun 2013

Its leaking out from behind the three way where it comes in contact with the block and we think the same think with the low pressure vavle
TimberlineShooter is offline   Reply With Quote
Old 06-17-2013, 07:23 PM   #4 (permalink)
Eric
 
lechooch's Avatar
 
Join Date: Mar 2009
Location: Southern California
Send a message via Skype™ to lechooch

im having the exact same issue with my orracle build
seems to be my 3way leaking but its hard to tell
__________________
Here are my current paintball activities:
Pirranah SB restoration:http://www.mcarterbrown.com/forums/c...n-project.html
Comprehensive High end SC marker review/comparison:http://www.mcarterbrown.com/forums/m...on-review.html
Youtube Chanel:http://www.youtube.com/user/TheLechooch/videos
Feedbackhttp://www.mcarterbrown.com/forums/f...-feedback.html
lechooch is online now   Reply With Quote
Old 06-17-2013, 07:26 PM   #5 (permalink)
Newbie
 
TimberlineShooter's Avatar
 
Join Date: Jun 2013

Its kinda odd of u ask me
We have a boring to help keep it from doing that there against the block but the seems it be leaking out around it
TimberlineShooter is offline   Reply With Quote
Old 06-17-2013, 09:52 PM   #6 (permalink)
Dr. says it will clear up
 
leathalh's Avatar
 
Join Date: Jun 2011
Location: Denver, Co

CCM Fan
Everytime I put an oring on my 3-way to keep it from leaking, it leaked. Take the oring off and see if it helps, on mine it pushed the 3-way too far out and caused the leak internally. There is no air to be contained between the 3-way and front block, it's all inside. The 3 way may not be snug up against the front block, just get it as close as you can and still have the barbs facing up, the hoses will hold it in place.
__________________
Autocockers are not more accurate, I'm just more accurate when I shoot autocockers.
leathalh is online now   Reply With Quote
Old 06-18-2013, 08:13 AM   #7 (permalink)
Seasoned Member
 
Join Date: Sep 2008
Location: Saxonburg, PA

if its leaking out the back of the 3-way, and the orings are good then it may need adjusted. now when you say the low pressure valve do you mean the valve inside the gun or the low pressure regulator on the front block?
__________________
Feedback
PBN
CC
tolar250 is offline   Reply With Quote
Old 06-18-2013, 09:58 AM   #8 (permalink)
Active Member
 
kvorkian's Avatar
 
Join Date: Apr 2012
Location: SoCal

what type of lpr and 3way are you using? stock? a leak at the 3way can require an adjustment, require o-rings to be replaced or could be the caused by a bent 3way rod. you might also check the ram. do you have a local shop you could send it? visit CC and you may find a local guy to help with the adjustments.
kvorkian is offline   Reply With Quote
Old 06-18-2013, 10:34 AM   #9 (permalink)
Newbie
 
TimberlineShooter's Avatar
 
Join Date: Jun 2013

The three way is stock and we have replaced all the orings
And what's funny about finding some one local is I am the local person, as I'm working at my local paintball store. and next nearest person is about an hours drive and with gas prices these days it sucks to drive out there not knowing if he will even be there.
TimberlineShooter is offline   Reply With Quote
Old 06-18-2013, 10:41 AM   #10 (permalink)
Newbie
 
TimberlineShooter's Avatar
 
Join Date: Jun 2013

When I say low pressure valve I do mean regulator
TimberlineShooter is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » WGP

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 03:28 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC