mcarterbrown.com

mcarterbrown.com (http://www.mcarterbrown.com/forums/)
-   The Yard Sale (http://www.mcarterbrown.com/forums/yard-sale/)
-   -   Real Steel: AR Parts (http://www.mcarterbrown.com/forums/yard-sale/223017-real-steel-ar-parts.html)

philosophia 01-08-2013 09:24 PM

Real Steel: AR Parts
 
Decided to sell the AR parts now that my plans for a build have been put on indefinite hold. I will try my best to ship within two business days, but I'm heading back to school on January 13th, so after that one of my parents will be shipping if anything is sold. I accept PayPal and money order. Anyways, onto the stuff.

All of the parts have never been used/fired, but some parts may have been installed and uninstalled. I've tried to list all the marks in the finishes and stuff.


Yankee Hill Machine Low Profile Gas Block -$28
Brand new in packaging. Fit's 0.750 OD barrel and uses set screws.

http://i1356.photobucket.com/albums/.../arsale006.jpg

Troy Battlesights (fixed) -$110
Front and rear sight combo. The front sight ears around the post are HK-style, which at least to me is easier to aim with. The screw for the rear sight has some markings from a screw driver.

http://i1356.photobucket.com/albums/.../arsale007.jpg
http://i1356.photobucket.com/albums/.../arsale008.jpg

Yankee Hill Machine Customizable Free Float Tube AND Yankee Hill Machine Free Float Wrench-$180
This is literally brand new in packaging. I've taken it out of the packaging once to look at it and then it went straight back into the sleeve. Rifle length hand guard.

http://i1356.photobucket.com/albums/...ki/sale001.jpg

Yankee Hill Machine 5C2 Muzzle Break-$45
Brand new in package. 5/8-24 threads, can be used on some AR-10s as well. The front is scalloped for "breaching and close quarters combat" :rolleyes: Includes crush washer.

http://i1356.photobucket.com/albums/...ki/sale011.jpg
http://i1356.photobucket.com/albums/...ki/sale012.jpg

Nikon P-Series Scope Mount-$40
Perfect for mount a scope or what have you on an AR. For 1" scopes and stuff.

http://i1356.photobucket.com/albums/...ki/sale004.jpg

DSA Upper Receiver AND Palmetto State Armory Charging Handle (7075 aluminum) -$110 PENDING PAYMENT
Pretty new upper with ejection port cover and forward assist. There are some small marks around the forward assist pin, where the rear takedown pin hole is, and the very rear of the receiver. The latter two won't show if when the upper is attached to a lower. The ejection port door detent also needs to be broken in, it makes closing the cover all the way and the initial opening require a little bit more effort (it's not hard to work by any means). It has M4 feed ramps and machined T-marks.

http://i1356.photobucket.com/albums/.../arsale002.jpg
http://i1356.photobucket.com/albums/.../arsale003.jpg
http://i1356.photobucket.com/albums/.../arsale009.jpg
http://i1356.photobucket.com/albums/.../arsale010.jpg
http://i1356.photobucket.com/albums/...ki/sale008.jpg

ALG Defense Combat Trigger AND Magpul Aluminum Enhanced Trigger Guard-$80 PENDING PAYMENT
The hammer shows some wear from rubbing against a bolt carrier, but in no way does it affect performance. As a matter of fact, you can't even feel the wear at all. Comes will all the pins for the hammer and trigger including the slave pin as well as the screw and pin for the trigger guard.
(Trigger and hammer details can be found here)

http://i1356.photobucket.com/albums/...ki/sale005.jpg
http://i1356.photobucket.com/albums/...ki/sale010.jpg

White Oak Armament 6.8 SPC Bolt-$65 SOLD
Brand new in package. Has never been installed in a rifle or bolt carrier for that matter.

http://i1356.photobucket.com/albums/...ki/sale007.jpg

Spikes Tactical ST-T2 Heavy Buffer-$30 SOLD
Heavier than your standard buffer, will reduce the felt recoil and reduce the cycle rate.

http://i1356.photobucket.com/albums/...ki/sale006.jpg

Palmetto State Armory 6-Position Mil-Spec Diameter Buffer Tube (7075 aluminum) AND Palmetto State Mil-Spec Carbine Buffer Spring AND Yankee Hill Machine Ambidextrous Sling Receiver End Plate-$40 SOLD
Everything you need to put a stock on an AR but a buffer (hint hint) and the actual stock itself. Includes the lock ring.

http://i1356.photobucket.com/albums/...ki/sale003.jpg

chopper duke 01-08-2013 10:05 PM

No trades, PB or otherwise?

philosophia 01-08-2013 10:52 PM

Forgot about that.

I'm open to offers on most trades.

I replied to PMs as well.

Sorry if this counts as a bump, I figured it'd be viewed easiest here.

EDIT: I don't really need any paintball parts or anything, I haven't played in over a year :(
My 007 still works good though :D

MrFancyPants 01-09-2013 12:51 AM

I'll take the 6.8 bolt and seconds on the upper and charging handle.

philosophia 01-09-2013 07:26 PM

Everything that has been sold has been shipped today and the listing was updated and organized.


All times are GMT -4. The time now is 04:43 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC