Easiest to order and find me on ebay - seller mpqtmagnum
Regulator piston seats to repair your High pressure or Low pressure regulators on EGOs!
Fix your high pressure and low pressure regulators.
When the seats get old and wear out, your pressures can creep and your consistency can go out the window.
These are made from new clear polyurethane with an extremely smooth surface for solid consistency.
New, fresh polyurethane, not old rotted aged stock from a decade ago.
These ship by by post office in a LETTER sized envelope.
Two Types to choose from:
TYPE A
These will fit the High pressure regulator pistons for Egos: 5,6,7,8 and SL66, SL74, SL8R.
(see pictures for piston example, piston not included.)
These will also fit the Low pressure regulator pistons for Egos: 5,6,7,8,9,10, 11, SL74, SL8R, Etek 3/4
(see pictures for piston example, piston not included.)
---------------------------------
Replacement:
- Carefully pick out the old regulator seat/seal.
- Fully remove the old material and clean out the piston cavity.
- Gently rough the smaller bottom of the new regulator seat with a fine sandpaper.
- Add a very small drop of epoxy or super glue to the bottom of the piston seat cavity.
- Press the new regulator seat into place in the regulator seat cavity with the large shiny side up.
- Let glue harden over night.
- Re-assemble regulator and tune pressures.
- Let it rip!
----------------------------------
TYPE B
These will fit the High pressure regulator pistons for:
Ego 9, Ego 10, SL94, Geo and ETEK 3.
---------------------------------
Replacement:
- Carefully pick out the old regulator seat/seal.
- Fully remove the old material and clean out the piston cavity.
- Carefully press the new regulator seat into place in the regulator seat cavity with the large shiny side up.
- Be sure not to damage the surface of the new seat during installation.
- Re-assemble regulator and tune pressures.
- Let it rip!
----------------------------------
Regulator piston seats to repair your High pressure or Low pressure regulators on EGOs!
Fix your high pressure and low pressure regulators.
When the seats get old and wear out, your pressures can creep and your consistency can go out the window.
These are made from new clear polyurethane with an extremely smooth surface for solid consistency.
New, fresh polyurethane, not old rotted aged stock from a decade ago.
These ship by by post office in a LETTER sized envelope.
Two Types to choose from:
TYPE A
These will fit the High pressure regulator pistons for Egos: 5,6,7,8 and SL66, SL74, SL8R.
(see pictures for piston example, piston not included.)
These will also fit the Low pressure regulator pistons for Egos: 5,6,7,8,9,10, 11, SL74, SL8R, Etek 3/4
(see pictures for piston example, piston not included.)
---------------------------------
Replacement:
- Carefully pick out the old regulator seat/seal.
- Fully remove the old material and clean out the piston cavity.
- Gently rough the smaller bottom of the new regulator seat with a fine sandpaper.
- Add a very small drop of epoxy or super glue to the bottom of the piston seat cavity.
- Press the new regulator seat into place in the regulator seat cavity with the large shiny side up.
- Let glue harden over night.
- Re-assemble regulator and tune pressures.
- Let it rip!
----------------------------------
TYPE B
These will fit the High pressure regulator pistons for:
Ego 9, Ego 10, SL94, Geo and ETEK 3.
---------------------------------
Replacement:
- Carefully pick out the old regulator seat/seal.
- Fully remove the old material and clean out the piston cavity.
- Carefully press the new regulator seat into place in the regulator seat cavity with the large shiny side up.
- Be sure not to damage the surface of the new seat during installation.
- Re-assemble regulator and tune pressures.
- Let it rip!
----------------------------------
Comment