instagram takipci satin al - instagram takipci satin al mobil odeme - takipci satin al

bahis siteleri - deneme bonusu - casino siteleri

bahis siteleri - kacak bahis - canli bahis

goldenbahis - makrobet - cepbahis

cratosslot - cratosslot giris - cratosslot

Announcement

Collapse
No announcement yet.

Help finding/fabricating a fitting....

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Help finding/fabricating a fitting....

    I was hoping someone could point me in the right direction (or potentially machine an air fitting for me).

    I'm looking for a 1/2" long 1/8" NPT Male to Male union with no nut between the ends. I've searches the deepest, darkest corners of the internet and can't find something like this anywhere in a small size like this.

    Essentially, I am looking for piece of threaded hollow rod, preferably brass, but I'm not picky at this point. I'd prefer a taper, but again, not picky...I'll use some hydraulic thread sealant if it needs some help.

    Could someone please point me to a website or someone who can help?

    Thanks in advance
    JeepDVLZ45's Feedback

    #2
    I picked up some aluminum like that for a project awhile ago. I think it was off of mcmcaster.

    What about these:
    https://www.mcmaster.com/standard-pi...read-type~npt/

    They are 3/4" long though.

    The problem is that taper threads need a certain length to them so finding one out of standard may be tough.

    Comment


    • JeepDVLZ45

      JeepDVLZ45

      commented
      Editing a comment
      I didn’t even consider the “length” for the taper!!

      That could explain why I’m having so much trouble. I’ll have to go to 1/8” NPS

      Thanks!!

    #3
    I have had that issue before ...
    Get a fitting of whatever length you can find and run a die on the end ... It will shorten it a bit and you keep the taper.

    Or take a fitting with the hex and run it on the lather to knock the hex out (and same as above, you can shorten it as desired with a die.
    Love my brass ... Love my SSR ... Hard choices ...

    XEMON's phantom double sided feed


    Keep your ATS going: Project rATS 2.0
    My Feedback

    Comment


      #4
      Tried the hardware store? I'm pretty sure thats where I got my version of what you're looking for.

      Otherwise, here's a link to a fitting... and the company that sells it has a ton of other stuff as well.

      https://www.mettleair.com/store/bras...e-1-8-npt.html
      And God turned to Gabriel and said: “I shall create a land called Canada of outstanding natural beauty, with majestic mountains soaring with eagles, sparkling lakes abundant with bass and trout, forests full of elk and moose, and rivers stocked with salmon. I shall make the land rich in oil so the inhabitants prosper and call them Canadians, and they shall be praised as the friendliest of all people.”

      “But Lord,” asked Gabriel, “Is this not too generous to these Canadians?”

      And God replied, “Just wait and see the neighbors I shall inflict upon them."

      Comment


      • JeepDVLZ45

        JeepDVLZ45

        commented
        Editing a comment
        This is exactly what I’ve been trying to find. I’ve been to every hardware store I could find with no luck and have been searching online for 4 months.

        Just ordered a couple for spares.

        Thanks again

      • Jordan

        Jordan

        commented
        Editing a comment
        Glad I could help!

      #5
      Originally posted by JeepDVLZ45 View Post
      I was hoping someone could point me in the right direction (or potentially machine an air fitting for me).

      I'm looking for a 1/2" long 1/8" NPT Male to Male union with no nut between the ends. I've searches the deepest, darkest corners of the internet and can't find something like this anywhere in a small size like this.

      Essentially, I am looking for piece of threaded hollow rod, preferably brass, but I'm not picky at this point. I'd prefer a taper, but again, not picky...I'll use some hydraulic thread sealant if it needs some help.

      Could someone please point me to a website or someone who can help?

      Thanks in advance
      What are you fixing/building?
      '96 RF Mini Cocker, '95 RF Autococker, Trilogy SF Autococker (mech'ed) , 68-Automag Classic, Banzai Splash Minimag, Warp Feed Gen 2 Micromag, Gen-E Matrix, Shoebox Shocker 4x4, Warp Feed Rainmaker, Mech'ed SP1 , Montneel Z-1, Tippmann Pro-Carbine, Tippmann Mini-Lite, Tippmann Model-98, Tippmann SL-68II , Tippmann 68-Special, Spyder .50 cal Opus/Opus-A , Spyder .50 cal Stormer

      Meleager7 Feedback: https://www.mcarterbrown.com/forum/b...ager7-feedback

      Comment


      • JeepDVLZ45

        JeepDVLZ45

        commented
        Editing a comment
        I’m just trying to find a short fitting so I can side-saddle one of my phantoms

        I literally have everything I need except the air fitting. I had purchased one that has the “nut”, but it keep the lever changer way too far from the body of the marker.
    Working...
    X