instagram takipci satin al - instagram takipci satin al mobil odeme - takipci satin al

bahis siteleri - deneme bonusu - casino siteleri

bahis siteleri - kacak bahis - canli bahis

goldenbahis - makrobet - cepbahis

cratosslot - cratosslot giris - cratosslot

Announcement

Collapse
No announcement yet.

Help finding/fabricating a fitting....

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • JeepDVLZ45
    commented on 's reply
    I’m just trying to find a short fitting so I can side-saddle one of my phantoms

    I literally have everything I need except the air fitting. I had purchased one that has the “nut”, but it keep the lever changer way too far from the body of the marker.

  • Meleager7
    replied
    Originally posted by JeepDVLZ45 View Post
    I was hoping someone could point me in the right direction (or potentially machine an air fitting for me).

    I'm looking for a 1/2" long 1/8" NPT Male to Male union with no nut between the ends. I've searches the deepest, darkest corners of the internet and can't find something like this anywhere in a small size like this.

    Essentially, I am looking for piece of threaded hollow rod, preferably brass, but I'm not picky at this point. I'd prefer a taper, but again, not picky...I'll use some hydraulic thread sealant if it needs some help.

    Could someone please point me to a website or someone who can help?

    Thanks in advance
    What are you fixing/building?

    Leave a comment:


  • Jordan
    commented on 's reply
    Glad I could help!

  • JeepDVLZ45
    commented on 's reply
    This is exactly what I’ve been trying to find. I’ve been to every hardware store I could find with no luck and have been searching online for 4 months.

    Just ordered a couple for spares.

    Thanks again

  • Jordan
    replied
    Tried the hardware store? I'm pretty sure thats where I got my version of what you're looking for.

    Otherwise, here's a link to a fitting... and the company that sells it has a ton of other stuff as well.

    https://www.mettleair.com/store/bras...e-1-8-npt.html

    Leave a comment:


  • XEMON
    replied
    I have had that issue before ...
    Get a fitting of whatever length you can find and run a die on the end ... It will shorten it a bit and you keep the taper.

    Or take a fitting with the hex and run it on the lather to knock the hex out (and same as above, you can shorten it as desired with a die.

    Leave a comment:


  • JeepDVLZ45
    commented on 's reply
    I didn’t even consider the “length” for the taper!!

    That could explain why I’m having so much trouble. I’ll have to go to 1/8” NPS

    Thanks!!

  • netsurferdude2
    replied
    I picked up some aluminum like that for a project awhile ago. I think it was off of mcmcaster.

    What about these:
    https://www.mcmaster.com/standard-pi...read-type~npt/

    They are 3/4" long though.

    The problem is that taper threads need a certain length to them so finding one out of standard may be tough.

    Leave a comment:


  • JeepDVLZ45
    started a topic Help finding/fabricating a fitting....

    Help finding/fabricating a fitting....

    I was hoping someone could point me in the right direction (or potentially machine an air fitting for me).

    I'm looking for a 1/2" long 1/8" NPT Male to Male union with no nut between the ends. I've searches the deepest, darkest corners of the internet and can't find something like this anywhere in a small size like this.

    Essentially, I am looking for piece of threaded hollow rod, preferably brass, but I'm not picky at this point. I'd prefer a taper, but again, not picky...I'll use some hydraulic thread sealant if it needs some help.

    Could someone please point me to a website or someone who can help?

    Thanks in advance
Working...
X