instagram takipci satin al - instagram takipci satin al mobil odeme - takipci satin al

bahis siteleri - deneme bonusu - casino siteleri

bahis siteleri - kacak bahis - canli bahis

goldenbahis - makrobet - cepbahis

cratosslot - cratosslot giris - cratosslot

Announcement

Collapse
No announcement yet.

What did you 3D print today?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Spider!
    commented on 's reply
    Which translucent filament is that?

    I have some 3dxtech yellow that prints pretty well, but I haven't done much with the transparency aspect.

  • Brokeass_baller
    replied
    Printed a Magpul MOE wanna-be for my 468. Feels great. Print shifted up around the beaver tail, and I'm not really sure why, but I can't feel it, so I'm leaving it. PLA+ has been printing very well for me lately, and it's much less brittle than the carbon fiber PLA I was playing with before. It's so shiny though. I might experiment with high grit Emery cloth to dull it.
    Attached Files

    Leave a comment:


  • Brokeass_baller
    commented on 's reply
    That looks really nice

  • RAZRBAKK
    commented on 's reply
    BrickHaus honestly this filament has just been printing very well for me. No idea what another roll will look like lol.

  • BrickHaus
    commented on 's reply
    Dude. You are pretty darn good at this. I can't dream of clear prints like this.

  • RAZRBAKK
    replied
    I've been experimenting with some ghost ring alternatives. Really enjoying this translucent filament.





    It's difficult to get a good shot of the sight picture, but I opted for fiber optic filament instead of the usual post.

    If anyone is interested in trying one of these, I am working through cleaning up the print a bit and have a ton of this filament, so I'd be happy to throw a few of these together at cost to see what people think. Can and will do black/CF-black.

    Leave a comment:


  • XEMON
    commented on 's reply
    CNC Kitchen did some great test on that RAZRBAKK posted the link above 👍

  • BrickHaus
    replied
    Fired up my printers after months of not even considering their existence. Couldn't get either to print a link. I'll have to mess with them some and see if it's something simple.

    So, the best thing I did with my printers all night was this cold pull.

    Leave a comment:


  • JonM
    commented on 's reply
    I wonder if it would be effective to design a part with a pocket for the insert, print it, then set the insert using epoxy resin or UV resin.

  • RAZRBAKK
    commented on 's reply
    Carp I agree, I want to like the grey but this is much nicer. I'm sanding it down as I don't love the gloss. Eventually I'm going to remake all the parts in CF PETG so that will have a nice matte to it.

  • Carp
    commented on 's reply
    This looks much nicer than the grey.

  • RAZRBAKK
    replied


    I feel like I'm getting into reconslide territory with this one. Print quality is massively improved on the black PETG vs grey. Just gotta clean up the stringing a bit.

    Leave a comment:


  • RAZRBAKK
    replied
    Slow day at work, so I've mostly been printing in between tasks.




    I'm starting to think the grey filament is just being problematic.
    These were printed a day apart, same settings, both post lead screw change, both dried in the filament dryer for 12 hours or more.
    One line near the top is somewhat consistent with each other, but the black filament has gone down MUCH better than the grey.

    Still fighting elephants foot. I have my bed cranked because I can't seem to get proper adhesion below 75 degrees, even on the PEI bed.
    I'm going to fire up some transparent filament this week.

    Lots to tune, but the prints are definitely improving over here.

    15 hour full-length pump handle in black coming up tomorrow.

    Leave a comment:


  • RAZRBAKK
    replied
    I swear I'll post something else soon, just been working through some revisions. I like the size of this one more for sure. Aesthetically I would still like to extend it closer to the barrel but I haven't found the height limit on my Ender 3 yet. Every part is more robust on each revision. I think I'm going to increase my infill and try to knock out as much pump wobble as I can. Probably 1-2 more runs at this guy before I'm happy with it.







    You can see my layer issue remains but it's improved a bit. I just replaced the lead screw and Z-axis nut, and i have a WobbleX on the way.

    I noticed my extruder is skipping a fair amout since switching to PETG. I guess that is the next thing to address. Not expecting perfection, just the best I can get out of a bed slinger.

    I'm going to try sanding this one a bit.

    Leave a comment:


  • XEMON
    commented on 's reply
    The heat crumbled the resin ...

    The hard wood inserts are the next step if the printed one don't hold up. But they all use proprietary male threads so I'll have to reverse engineer those to ensure proper fit
Working...
X