instagram takipci satin al - instagram takipci satin al mobil odeme - takipci satin al

bahis siteleri - deneme bonusu - casino siteleri

bahis siteleri - kacak bahis - canli bahis

goldenbahis - makrobet - cepbahis

cratosslot - cratosslot giris - cratosslot

Announcement

Collapse
No announcement yet.

Aluminum Fittings/ NPT Elbows?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Aluminum Fittings/ NPT Elbows?

    When you run out of things to do...

    Looking at replacing the old classic nickel-plated elbow fittings on a mag with anodized aluminum elbows.

    I'm sure they're fine for 850psi, but just want to make sure if anyone has had any issues. The ones I'm looking at are 6061, just wanted to know pros/cons.

    Thank you.

    #2
    I have used the CCM and Nummech ones without issue.
    The CCM are a finer product.
    Need Inception Designs or Shocktech Products? Let me know!

    MCB Feedback

    old PBN feedback

    Comment


      #3
      They'll be more likely to gall. Use a lubricant like threadlocker or teflon paste.
      Feedback: https://www.mcarterbrown.com/forum/b...eedback-thread
      Nelspot/CCI Sears and Triggers
      Action Markers Valves

      Comment


        #4
        Originally posted by Hellion360 View Post
        I have used the CCM and Nummech ones without issue.
        The CCM are a finer product.
        What's the difference?

        Sent from my Moto Z (2) using Tapatalk

        I use Tapatalk which does NOT display comments. If you want me to see it, make it a post not a comment.

        Feedback
        https://www.mcarterbrown.com/forum/b...323-s-feedback

        Comment


          #5
          Originally posted by Trbo323 View Post
          What's the difference?

          Sent from my Moto Z (2) using Tapatalk
          Just design really. Nummech uses all 010 orings in their fittings while CCM uses different sizes.

          Sent from my Pixel 4a using Tapatalk

          Comment


            #6
            Originally posted by Toestr View Post
            Just design really. Nummech uses all 010 orings in their fittings while CCM uses different sizes.

            Sent from my Pixel 4a using Tapatalk
            Good to know thanks, I've been thinking of getting a few

            Sent from my Moto Z (2) using Tapatalk

            I use Tapatalk which does NOT display comments. If you want me to see it, make it a post not a comment.

            Feedback
            https://www.mcarterbrown.com/forum/b...323-s-feedback

            Comment


              #7
              If you're talking about those anodized aluminum 1/8 elbows that you would thread steel braided line into, they tend to be leak prone as they are pivot elbows with an O ring in between and the O ring is usually old by now. I don't know if there is a way to replace it as I think they're pressed together.

              Comment


                #8
                Originally posted by Cunha View Post
                If you're talking about those anodized aluminum 1/8 elbows that you would thread steel braided line into, they tend to be leak prone as they are pivot elbows with an O ring in between and the O ring is usually old by now. I don't know if there is a way to replace it as I think they're pressed together.
                I've seen those made by extreme rage and avoid those, I'm certain they are deteriorated by now as well.

                The ones I ordered are fixed anodized aluminum, 6061.

                Comment


                  #9
                  Originally posted by Cunha View Post
                  If you're talking about those anodized aluminum 1/8 elbows that you would thread steel braided line into, they tend to be leak prone as they are pivot elbows with an O ring in between and the O ring is usually old by now. I don't know if there is a way to replace it as I think they're pressed together.
                  I've been looking for something like those forever, and can't find anything that's a reasonable cost or form factor.

                  I contacted nummech suggesting making some based on their banjos and heard nothing back. Also contacted a local store that does some fabrication and they were interested but had too much on their plate.

                  Sent from my Pixel 4a using Tapatalk


                  Comment


                    #10
                    Originally posted by Advanced View Post

                    I've seen those made by extreme rage and avoid those, I'm certain they are deteriorated by now as well.

                    The ones I ordered are fixed anodized aluminum, 6061.
                    Where have you found anodized elbow fittings? I would really like to get some color matched elbows for several of my older markers, where I prefer braided hose.

                    Also - I wholeheartedly agree that the Extreme Rage elbows are to be considered broken out of the box. Should anyone figure out how to rebuild them, I'm all ears.
                    Got Bork?

                    Olsson's WTB - Shut up and take my money!

                    Comment


                      #11
                      https://www.ebay.com/itm/1-8-NPT-Str...-127632-2357-0

                      I bought these, but I'm a hesitant to air up my automag with them. I'm running 900psi tank output, I can't find any accurate pressure rating for these.

                      They are 6061 aluminum
                      ​​​​​​

                      Comment


                        #12
                        Over on mcmaster, there's similar later at 500psi:

                        McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.


                        Anyone ever use aluminum elbows?

                        Comment

                        Working...
                        X