Pre 2k Sheridan internal upgrade to later pre2k?

[Aididas78]

AKA also sells the older pre-97 style springs for your valve. I just purchased a lower tube kit from them that works well. I’d get the pre 97 valve spring with the hammer kit. The hammer kit comes with the hammer, hammer spring, and rear velocity adjuster. You can use a new style valve such as a plain WGP valve, AKA tornado valve (pretty expensive), or a rat. There’s plenty of WGP valve copies out there that work just fine. If you tap out the lower tube you can’t use a Beavertail anymore if you care about that. I’d just drill the lug adjustment hole with a drill press from the top straight down and you’re done.

[OpusX]

Ah yes the shorter valve springs! This could also be part of your velocity fun from the other thread

[Myrkul]

Just to echo what everyone else said:

Get a new style valve & hammer of your choice, Nelson springs, and a Non-threaded IVG and get the hole punched in the top. I had to do this on a 96 Cocker a few years ago and it absolutely rips now. I ended up using a OTP non-threaded IVG.

Be sure to trim your valve spring down a bit to work too, the pre 97 bodies that use sheridan springs had smaller valve chambers.

[iamthelazerviking]

I'd vote drilling for hammer lug adjustment plus threading for IVG. Not expensive to have done, run better internals in an older body

[superman]

i recognize that picture. If you need help drilling the lug hole, tapping the body for an ivg or even purchasing the shocktech lowertube kit, let me know. Happy to help.

[OpusX]

I ment the hammer.

The picture I posted wasnt a hammer it is a Nelson spring colpatible non-threaded IVG.


The ANS kit Walker posted ( https://ansgear.com/ans-autococker-n...ded-hammer-kit) includes the IVG and a hammer which has a top hole adjustable lug.

[tracythompsontampa]

These are adjusted from the rear by removing the cocking rod just like threaded ivgs.

I ment the hammer.

[OpusX]

Can I adjust the ANS one from the top of the body? I can't find another view of it online.

These are adjusted from the rear by removing the cocking rod just like threaded ivgs.

[tracythompsontampa]

You need a pre2k nonthreaded Nelson IVG. The Nelson ivg is wide enough for the bigger Nelson springs OD. Also it has a plunger inside that fits the ID of the spring.

The Sheridan ivg (probably just a cap with different mounting holes to adjust depth) wont be wide enough to fit the springs.

Can I adjust the ANS one from the top of the body? I can't find another view of it online.

[tracythompsontampa]

Awesome thank you for the info. I'll order from one of the links above

[Meleager7]

this happened to me as well!

[Cdn_Cuda]

Also, newer hammer lungs are wider than old ones, so on my Pre-2K conversion I could not use a newer hammer as the slot on the body was too small for the hammer lug.

Refer to second page, post #16:

https://www.mcarterbrown.com/forum/paintball-news-aa/the-armory/autocockers/379062-quick-compo-2k-vs-pre-2k-cockers/page2

[Walker]

ANS still sells a non-threaded IVG: https://ansgear.com/ans-autococker-non-threaded-ivg

Or a kit: https://ansgear.com/ans-autococker-n...ded-hammer-kit

[OpusX]

You need a pre2k nonthreaded Nelson IVG. The Nelson ivg is wide enough for the bigger Nelson springs OD. Also it has a plunger inside that fits the ID of the spring.

The Sheridan ivg (probably just a cap with different mounting holes to adjust depth) wont be wide enough to fit the springs.

[Walker]

1. Can I use my old IVG with these newer pre2k kits?
- Answer: No, the spring diameters are different

2. Will the new hammer work with my old IVG?
- Answer: No, same reason as above

Solution: Get a newer lower kit with a non-threaded IVG, or have the body threaded for a new IVG.

AKA has a non-threaded pre2k hammer/IVG kit: https://akapaintball.com/index.php?p...cts/hammer-kit