Tippmann Springs and O-rings chart

[The Inflicted]

Saved from a cached Google page.
I have no idea if this is accurate or not but I needed some of this info this evening and figured I'd be a good citizen and repost it to save it for the next person.

As posted by @chandlercv

https://www.mcarterbrown.com/forums/...reference.html

https://webcache.googleusercontent.c...&ct=clnk&gl=us

SL-68 II
	O-Rings
	- Front Bolt: SL2-19 -112 70A durometer Buna
	- Valve Seat: SL2-25 -012 70A durometer Urathane
	- End Cap: SL2-4 -015 70A durometer Buna
	Springs
	- Hammer: OD: 3/8 in. (+/-1/16) WD: 1/32 in. Length: 2 3/8 in. Pitch: 5 cpi
	- Valve: OD: 3/8 in. (+/-1/16) WD: 1/32 in. Length: 7/16 in. Pitch: 5 cpi
	Screws:
	- Barrel pinch: 1/4-20 thd, 3/4" length
	- Hopper pinch: 1/4-20 thd, 7/8" length
	Pro-Lite
	O-Rings
	- Front bolt: PA-18 -015 90A durometer Urathane
	- Valve body: PA-12 -017 70A durometer Urathane
	- Internal Valve Seat: SL2-25 -012 70A durometer Urathane
	- Hammer: PA-12 -017 70A durometer Urathane
	Springs
	- <No data available>
	Screws
	- Barrel pinch bolt: 1/4-20 thd, 5/8" length
	- Elbow pinch bolt: 1/4-20 thd, 1" length
	- Gripframe mount bolts: 10-32 thd, 3/8" length
	- Gripframe half bolt (top): 10-32 thd, 7/8" length
	- Gripframe half bolt (bottom): 10-32 thd, 1 1/4" length
	- Velocity adjustment bolt: 1/4-28 thd, 3/4" length set screw
	- Gripframe mount sleeves: 10-32 thd internal, 5/8" length, 1/4" diameter
	Pro/Carbine
	O-Rings
	- Front bolt: PA-18/FA-17 -015 90A durometer Urathane
	- Valve body: PA-12 -017 90A durometer Urathane
	- Internal Valve Seat: SL2-25 -012 70A durometer Urathane
	- Hammer: PA-12 -017 90A durometer Urathane
	- Valve Reduction Fitting: CA-09E M1x4.5 70A durometer Buna
	Springs
	- Valve: OD: 3/8 in. (+/-1/16) WD: 1/32 in. Length: 3/4 in. Pitch: 4 cpi
	- Hammer: OD: 3/16 in. (+/-1/32) WD: 1/32 in. Length: 4 3/8 in.(+/-1/8) Pitch: <no data>
	Screws
	- Barrel pinch bolt: 1/4-20 thd, 5/8" length
	- Elbow pinch bolt: 1/4-20 thd, 1" length
	- Gripframe mount bolts: 10-32 thd, 3/8" length
	- Grip panel bolts: 6-32 thd, 3/8" length
	- Bottomline mount bolts: 10-32 thd, 1" length
	- Velocity adjustment bolt: 1/4-20 thd, 7/8" length
	M98
	O-Rings
	- Front bolt: SL2-4 -015 70A durometer Buna
	- Valve body: 98-12A -019 70A durometer Urathane
	- Internal Valve Seat: SL2-25 -012 70A durometer Urathane
	- Hammer: 98-12A -019 70A durometer Urathane
	Springs
	- <No data available>
	Screws
	- Elbow pinch bolt: 1/4-20 thd, 1" length
	- Elbow latch bolts: 6-32 thd, 1/4" length (Holding the part that catches the front sight)
	- Main half bolts: 10-32 thd, 5/8" length
	- Foregrip half bolt: 10-32 thd, 1 1/8" length
	- Grip panel bolts: 6-32 thd, 3/8" length
	- Bottomline mount bolts: 10-32 thd, 1" length
	- Valve bolts: 10-32 thd, 1/4" length
	- Velocity adjustment bolt: 1/4-28 thd, 3/8

[lew]

Outstanding. Thanks for that!

[Axel]

Ooooh thank you for this

[Myrkul]

Tippmann 68 Special "O" Ring Sizes

Front Bolt "O" Ring: #015 (9/16 ID 11/16 OD 1/16 Wall)
Front Bolt Linkage Arm Retainer: #011 (5/16 ID 7/16 OD 1/16 Wall)
Power Tube Face Seal: #116 (3/4 ID 15/16 OD 3/32 Wall)
Internal Valve Seal Front: #012 (3/8 ID 1/2 OD 1/16 Wall)
Internal Valve Seal Back: #012 (3/8 ID 1/2 OD 1/16 Wall)
External Valve Seal: #020 (7/8 ID 1" OD 1/16 Wall)
Hammer Face Seal: #020 (7/8 ID 1" OD 1/16 Wall)
Hammer Linkage Arm Retainer: #011 (5/16 ID 7/16 OD 1/16 Wall)

Probably go urethane wherever you can because Liquid Co2, but mine is mostly buna and works fine.

[Brokeass_baller]

Anybody know what size the 98C and A5 bumper o-rings are? I know it isn't a crucial o-ring, but I'm afraid too large might cause burping, and too small might cause rear cap damage.

[glaman5266]

Anybody know what size the 98C and A5 bumper o-rings are? I know it isn't a crucial o-ring, but I'm afraid too large might cause burping, and too small might cause rear cap damage.

Here's a chart with an A-5 o-ring list with o-ring numbers & sizes in inches. Found it in an old PbN thread. Apparently this doc was originally from the old A5OG. Doesn't list durometers though.

https://docs.google.com/spreadsheets...AV4/edit#gid=1

And here's the aforementioned thread from PbN, which also has the IDs and ODs in millimeters.

https://www.pbnation.com/showthread.php?t=4420729

[Chandlercv]

An errata:
The hammer and valve body o-ring hardness for carbines and pro-carbines should be 70A.

[Dusty Bottoms]

This should get stickied.

[glaman5266]

I agree. Chappy Axel

[Tippster]

Anyone know the size of the o-rings inside the FA shock housing?

[Trbo323]

Anyone have one of these for the A5? Seems like there was a change in the tombstone ring at some point, I'm trying to figure out the old and new sizes

[Carp]

Anyone have one of these for the A5? Seems like there was a change in the tombstone ring at some point, I'm trying to figure out the old and new sizes

Post #6, in this thread, might have the info you are looking for.

[Trbo323]

Post #6, in this thread, might have the info you are looking for.

Only kind of. It lists a 111 which is what I've typically used but I'm assuming that's the old size, I'm not sure on that, doesn't list any other size or durometer (I suspect 90 but again, never seen actual specs)

Sent from my motorola edge 5G UW (2021) using Tapatalk

[SuperActionMan]

Tippmannparts.com says the change was in 2011 and which one you have can be determined by measuring the valve body length. 1 15/16" (1.938", 49.2mm) is the old one that uses the smaller o-ring. They don't list the trade number, of course.

Do you have calipers that you can measure the old one with? They are easy to cross-ref since Tippmann uses mostly(or entirely?) standard American AS568B inch sizes. I only have an early A5 right now, but a 2011+ ought to be here today. I'll probably have it apart and can measure that o-ring if needed.

[Toestr]

I believe they used at least one metric oring in the Flex Valve. The orings between the body and trigger/valve block on the Crossover are some Parker proprietary oring but it's a very similar size to 3x1mm so those may work (some Dow55 may be required).

[Trbo323]

Tippmannparts.com says the change was in 2011 and which one you have can be determined by measuring the valve body length. 1 15/16" (1.938", 49.2mm) is the old one that uses the smaller o-ring. They don't list the trade number, of course.

Do you have calipers that you can measure the old one with? They are easy to cross-ref since Tippmann uses mostly(or entirely?) standard American AS568B inch sizes. I only have an early A5 right now, but a 2011+ ought to be here today. I'll probably have it apart and can measure that o-ring if needed.

Sold that marker

I know one of them, I believe the old one is a 111 I just don't know what the new one is

Sent from my motorola edge 5G UW (2021) using Tapatalk

[lhamilton1807]

I am working on a buddy's Crossover and have compiled a list of o-rings:

Manual Pt#	Tippmann Pt#	Qty/rebuild	Where Used?	Duro & Size
3	TA20046	1	Front bolt bumper	70A 118
4	02-40	1	Barrel	70A 019
10	TA20047	3	Valve body manifold	70A 5-178
14	TA35096	2	Valve core o-ring	70A 002
24	TA30040	1	Power tube	70A 019
27	TA35016	6	Air Valve Assy End cap	70A 021
28	TA30050	2	Inner air valve Valve end cap	70A 011
31	TA35076	1	Valve spool bumper	90A 010
54	TA35055	1	Regulator piston (lg)	70A 013
55	TA35087	1	Regulator piston (sm)	90A 004
69	18-PA	1	Fore grip seal	90A 015
	TA30049	6	spool - sm / air tsfr tube	70A 008
	TA20003	1	spool - large	70A 010

Also, I found the ultimate Tippmann parts list, which actually includes durometer and seal size, not just the Tippmann catalog # that's in the manual. All other parts for all models are also included.
Tippmann-Markers-Parts-List-July-22