mcarterbrown.com  

Ask The Experts You ask the tough questions

Reply
 
Thread Tools Search this Thread
Old 01-14-2020, 08:39 PM   #1 (permalink)
Newbie
 
Join Date: Jan 2020

Autococker timing

Some burst go just fine.
Sometimes it hangs up with back push out then slowly closes
Any tips on where to start?
BrendanB is offline   Reply With Quote
Old 01-14-2020, 08:45 PM   #2 (permalink)
MCB Member
 
autococker04's Avatar
 
Join Date: Aug 2007
Location: Pittsburgh

I'd lube my three way and trigger plate.
__________________
Feedback!
autococker04 is online now   Reply With Quote
Old 01-14-2020, 08:52 PM   #3 (permalink)
Super Legit
 
Trbo323's Avatar
 
Join Date: May 2012
Location: Vancouver, Washington

Quote:
Originally Posted by autococker04 View Post
I'd lube my three way and trigger plate.
I'd start here as well.

Also, move your back block by hand, see if anything is hanging up that you can feel
__________________
https://www.mcarterbrown.com/forums/n...ml#post2612544

^^^ If you are new to the sport and need help finding gear, click here!!!^^^


feedback: https://www.mcarterbrown.com/forums/f...-feedback.html
Trbo323 is offline   Reply With Quote
Old 01-14-2020, 09:14 PM   #4 (permalink)
pumper, machinist
 
Join Date: Jul 2018
Location: 1hr east of Atlanta

everything they said ^^^^
and if no go, maybe a piece of debris in the front ram barb/line, if it is dropping forward slowly
440SUPERCOMMANDO is offline   Reply With Quote
Old 01-15-2020, 02:08 AM   #5 (permalink)
Super Legit
 
Trbo323's Avatar
 
Join Date: May 2012
Location: Vancouver, Washington

Quote:
Originally Posted by 440SUPERCOMMANDO View Post
everything they said ^^^^
and if no go, maybe a piece of debris in the front ram barb/line, if it is dropping forward slowly
I'd think this would cause slow travel in both directions because that air has to evacuate through the same line

Edit: not if running qev I just realized, it's possible
__________________
https://www.mcarterbrown.com/forums/n...ml#post2612544

^^^ If you are new to the sport and need help finding gear, click here!!!^^^


feedback: https://www.mcarterbrown.com/forums/f...-feedback.html
Trbo323 is offline   Reply With Quote
Old 01-15-2020, 11:31 AM   #6 (permalink)
Newbie
 
Join Date: Jan 2020

Oiled slider and 3way.
Seems better! Thanks
BrendanB is offline   Reply With Quote
Old 01-15-2020, 12:01 PM   #7 (permalink)
Super Legit
 
Trbo323's Avatar
 
Join Date: May 2012
Location: Vancouver, Washington

Quote:
Originally Posted by BrendanB View Post
Oiled slider and 3way.
Seems better! Thanks
You may want to take that slider out at some point and really clean it and the trigger frame. I would expect your issues to come back once that oil thins out
__________________
https://www.mcarterbrown.com/forums/n...ml#post2612544

^^^ If you are new to the sport and need help finding gear, click here!!!^^^


feedback: https://www.mcarterbrown.com/forums/f...-feedback.html
Trbo323 is offline   Reply With Quote
Old 01-15-2020, 12:03 PM   #8 (permalink)
MCB Member
 
Gabe's Avatar
 
Join Date: Mar 2006
Location: Wasilla, AK
Send a message via MSN to Gabe

I had a similar issue on a gun that the LPR was set too high. Sometimes that can cause the 3-way to stick.

Try pushing the back block forward or back when aired up. It should move but only with moderate hand pressure.
Gabe is offline   Reply With Quote
Old 01-15-2020, 02:54 PM   #9 (permalink)
Newbie
 
Join Date: Jan 2020

yea its super tight, may need to set the whole system lower
BrendanB is offline   Reply With Quote
Old 01-15-2020, 03:42 PM   #10 (permalink)
MCB Member
 
Gabe's Avatar
 
Join Date: Mar 2006
Location: Wasilla, AK
Send a message via MSN to Gabe

If your LPR is adjustable then turn it down until the 3-way starts to leak and then turn it back up until the gun cycles smoothly. With the trigger held back you should be able to push the bolt in with just 5lbs of force or so. A well tuned autococker will pinch paint without breaking it.
Gabe is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » Ask The Experts

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 09:49 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO
© MCB Network LLC