mcarterbrown.com  

Brass Eagle Brass Eagle owners can hang out here

Reply
 
Thread Tools Search this Thread
Old 08-10-2013, 07:02 AM   #1 (permalink)
Newbie
 
Join Date: Jul 2013

Brass Eagle Raptor O Rings + barrel info reqd.

Hi , i have recently started resurrecting a dead Raptor and am missing a few parts, mainly the pin that drops into the bolt, the duck bill ASA, the barrel and a few o rings.
i have already repaired the valve so that the valve pin can move freely and im going to machine a new pin up in the next week or so, however i need to replace some/all of the o rings and cant find out what the sizes of each o ring are.

does anybody have this information so that i can get some replacement o rings to fit.

also, what threading does the raptor use for its barrel, is it spyder?
Techie is offline   Reply With Quote
Old 08-10-2013, 02:25 PM   #2 (permalink)
ҿ
 
splat15k's Avatar
 
Join Date: Jan 2008

I don't have any specific o-ring size information, but perhaps this website will be helpful: Brass Eagle Raptor Parts

Raptor barrels are uniquely threaded so spyder barrels will not work.
splat15k is offline   Reply With Quote
Old 08-10-2013, 05:06 PM   #3 (permalink)
Newbie
 
Join Date: Jul 2013

Quote:
Originally Posted by splat15k View Post
I don't have any specific o-ring size information, but perhaps this website will be helpful: Brass Eagle Raptor Parts
unfortunately that site lists the sizes in a way that i cant find the standard for.
if anybody has any information on how read the sizings that would be great.

the sizings are given in 3 letters, eg JAF for the bolt o rings.

as for the barrel, if i cant source an original i may have to re thread another barrel or come up with some sort of adapter.
Techie is offline   Reply With Quote
Old 08-10-2013, 05:27 PM   #4 (permalink)
ҿ
 
splat15k's Avatar
 
Join Date: Jan 2008

Quote:
Originally Posted by Techie View Post
unfortunately that site lists the sizes in a way that i cant find the standard for.
if anybody has any information on how read the sizings that would be great.

the sizings are given in 3 letters, eg JAF for the bolt o rings.

as for the barrel, if i cant source an original i may have to re thread another barrel or come up with some sort of adapter.
The site doesn't list the sizes; but perhaps you can contact them for that info if all other avenues are exhausted.
splat15k is offline   Reply With Quote
Old 08-10-2013, 06:04 PM   #5 (permalink)
Born again
 
mustangii's Avatar
 
Join Date: May 2006
Location: Warrensburg MO
Send a message via AIM to mustangii

Raptor uses the same barrel thread as the F-1 Illustrator.
Found this on ebay...
https://www.ebay.com/sch/Paintball-/16045/i.html?_from=R40&_nkw=Brass+eagle+raptor

Some parts are still in stock here...

https://www.jtpaintballparts.com/Bras...arts-s/225.htm

ed
__________________
Will no longer be selling anything outside of North America

ASE certifed master tech
Master Certified Chrysler Tech

Last edited by mustangii; 08-10-2013 at 06:08 PM.
mustangii is offline   Reply With Quote
Old 08-10-2013, 07:03 PM   #6 (permalink)
Rec Poster
 
DarinSTL's Avatar
 
Join Date: Jul 2013
Location: St Louis

Try a 016 oring.
DarinSTL is offline   Reply With Quote
Old 08-11-2013, 12:58 AM   #7 (permalink)
Old Mech's Warrior
 
Join Date: Jul 2009
Location: Cobourg,Ontario,Canada

research F1, F-4 Illustrator Manual. The Raptor is a exact clone of the illustrator. o- ring sizes of all the internals are an exact match and the F series Manual has the sizes in standard measurements. #10's & #13's if i remember correctly, but the manual has the exact numbers you will need.
Barrels are also an exact match for threading in the F1, but are getting harder to find.
good luck.
Rolling Thunder 67 is offline   Reply With Quote
Old 08-11-2013, 01:01 AM   #8 (permalink)
Newbie
 
Join Date: Jul 2013

I have found some barrels on ebay. Or I can use a lapco barrel adapter. Will look for an f1 manual
Techie is offline   Reply With Quote
Old 08-11-2013, 04:59 AM   #9 (permalink)
Newbie
 
Join Date: Jul 2013

so i have found the o rings from a F1 manual, they are for future reference as follows.

2x 013 90D Urethane (front of valve and resovior plug)
3x 013 70D Nitrile (all other small oring locations)
3x 016 70D Nitrile (2 on the bolt and 1 on the bolt plug)

SIZE=ID=OD+NW
013=7/16"=9/16"=1/16"
016=5/8"=3/4"=1/16"
Techie is offline   Reply With Quote
Old 08-11-2013, 12:28 PM   #10 (permalink)
ҿ
 
splat15k's Avatar
 
Join Date: Jan 2008

Nice find! Is there a master database that we can update?
splat15k is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » Brass Eagle

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 04:10 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO
© MCB Network LLC