mcarterbrown.com  

Showing results 1 to 40 of 400
Search took 0.31 seconds.
Search: Posts Made By: magmoormaster
Forum: The Dead Zone Today, 11:11 PM
Replies: 52
Views: 986
Posted By magmoormaster
I've had shocktech alien bolts in 2 cockers of...

I've had shocktech alien bolts in 2 cockers of mine, and was perfectly satisfied with them. They don't have o-rings, so you'll see a decrease in efficiency vs other bolts. But they work just fine.
...
Forum: The Dead Zone Yesterday, 11:20 PM
Replies: 52
Views: 986
Posted By magmoormaster
Sounds like you want CCM then.

Sounds like you want CCM then.
Forum: The Dead Zone Yesterday, 04:53 PM
Replies: 52
Views: 986
Posted By magmoormaster
I do. There's a reason why modern electros run in...

I do. There's a reason why modern electros run in the sub-200 PSI range. It's gentler on paint. Lower pressure -> less explosive expansion -> less ball breakage from power pulse. I don't ever have...
Forum: The Dead Zone Yesterday, 02:51 PM
Replies: 52
Views: 986
Posted By magmoormaster
That body will need 11/16" valves. So your...

That body will need 11/16" valves. So your options are going to be limited compared to 9/16", but all of the options are actually good haha. Basically you're looking at:

-Inception
-AKA (you'll...
Forum: Misc Paintball Items Yesterday, 01:54 AM
Replies: 16
Views: 866
Posted By magmoormaster
How much for the TV remote?

How much for the TV remote?
Forum: Misc Paintball Items Yesterday, 01:53 AM
Replies: 4
Views: 192
Posted By magmoormaster
Is that a top cocking or side cocking body?...

Is that a top cocking or side cocking body? Threaded feedneck or no?
Forum: The Dead Zone Yesterday, 01:51 AM
Replies: 52
Views: 986
Posted By magmoormaster
How are they the new hawtness? They've been used...

How are they the new hawtness? They've been used on high end cocker builds for about 2 decades, ever since they came out.

Never seen aka bolts decrease velocity. In all of my testing, comparing...
Forum: The Dead Zone 09-12-2019, 11:38 AM
Replies: 52
Views: 986
Posted By magmoormaster
There are certainly cheaper options for...

There are certainly cheaper options for pneumatics than Inception, but better? That's a little harder to say. The 3-way and ram from Inception are really top notch. I don't love the LPR (too big and...
Forum: The Dead Zone 09-11-2019, 02:59 PM
Replies: 16
Views: 457
Posted By magmoormaster
Prices on ebay, especially items that have been...

Prices on ebay, especially items that have been sitting for a while, are never accurate. $350 is absurd for an MQ valve.
Forum: The Dead Zone 09-11-2019, 11:49 AM
Replies: 16
Views: 457
Posted By magmoormaster
But you don't need an MQ valve to do this. That's...

But you don't need an MQ valve to do this. That's what I don't understand. You're looking at paying $200+ extra for a part that nets you nothing.
Forum: Ask The Experts 09-11-2019, 01:32 AM
Replies: 8
Views: 215
Posted By magmoormaster
Definitely the first version of the ACI 3-ways....

Definitely the first version of the ACI 3-ways. The ones you'll see on google are a later version.
Forum: The Dead Zone 09-10-2019, 03:44 PM
Replies: 16
Views: 457
Posted By magmoormaster
https://encrypted-tbn0.gstatic.com/images?q=tbn:AN...

https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcT8DaAsf-90w77PJu0AZHqBJLyVGl6fwO5eCdI87T8n06oAgXUG

A/T pneumatic assist makes sense. A/T MQ makes sense. But pneumatic assist MQ makes no...
Forum: Ask The Experts 09-10-2019, 03:32 PM
Replies: 10
Views: 225
Posted By magmoormaster
I'm of the opinion that if it doesn't leak, or...

I'm of the opinion that if it doesn't leak, or cause undue friction from swelling, don't change it. Removing the valve is way more work than it's worth.
Forum: WTB 09-09-2019, 01:42 PM
Replies: 5
Views: 157
Posted By magmoormaster
The correct word you're looking for is "lid." ...

The correct word you're looking for is "lid."

You can use the lid from any standard gravity feed you have lying around. But yes, you will need to disassemble the shells to put the lid on that pin....
Forum: Collectors Corner 09-09-2019, 01:40 PM
Replies: 42
Views: 4,617
Posted By magmoormaster
Nice, those Cromes are super cool. I would love...

Nice, those Cromes are super cool. I would love to get one myself.
Forum: CCI 09-05-2019, 11:09 PM
Replies: 33
Views: 831
Posted By magmoormaster
Sooooo, like a Retro 7.

Sooooo, like a Retro 7.
Forum: Ask The Experts 09-05-2019, 08:45 PM
Replies: 13
Views: 284
Posted By magmoormaster
RVA is a rear velocity adjuster. The vertical ASA...

RVA is a rear velocity adjuster. The vertical ASA is just called a vertical adapter.
Forum: Ask The Experts 09-05-2019, 11:50 AM
Replies: 13
Views: 284
Posted By magmoormaster
Paging Apamburn. Apamburn to the Ask the Experts...

Paging Apamburn. Apamburn to the Ask the Experts Isle.

Apamburn has a 98 set up to run at mid pressure (5-600 range IIRC) and it ran fine without a volumizer until some of the more recent changes...
Forum: The Dead Zone 09-04-2019, 07:32 PM
Replies: 45
Views: 963
Posted By magmoormaster
Not with an 11/16" valve. They go in just like a...

Not with an 11/16" valve. They go in just like a spyder or other STBB, just a lock screw on the bottom.
Forum: The Dead Zone 09-04-2019, 05:48 PM
Replies: 45
Views: 963
Posted By magmoormaster
Those are the only unique items. I mean, you'll...

Those are the only unique items. I mean, you'll need a mini length pump arm instead of a full size, but that's just because it's a mini body.
Forum: The Dead Zone 09-04-2019, 03:48 PM
Replies: 45
Views: 963
Posted By magmoormaster
Nice. Just be aware that it will require an...

Nice. Just be aware that it will require an Inception Designs trigger frame and 11/16" valves.
Forum: Autocockers 09-04-2019, 11:30 AM
Replies: 17
Views: 319
Posted By magmoormaster
Only Inception and Empire guns are different.

Only Inception and Empire guns are different.
Forum: Autocockers 09-04-2019, 02:23 AM
Replies: 17
Views: 319
Posted By magmoormaster
Yes to frame, yes to 2k length bolts, no to lower...

Yes to frame, yes to 2k length bolts, no to lower tube. Well, most of it will work, but the valve will not. You need an 11/16" valve.
Forum: Sheridan 09-03-2019, 11:03 AM
Replies: 17
Views: 498
Posted By magmoormaster
That's really slick. How did you attach the...

That's really slick. How did you attach the magwell to the body?
Forum: The Dead Zone 09-03-2019, 11:00 AM
Replies: 45
Views: 963
Posted By magmoormaster
What body did you get?

What body did you get?
Forum: Autocockers 09-01-2019, 12:43 AM
Replies: 25
Views: 491
Posted By magmoormaster
Doc is a bit of an idiot, tbh. I disagree with a...

Doc is a bit of an idiot, tbh. I disagree with a large amount of what he says.
Forum: Electronic and Mechanical 08-31-2019, 06:05 PM
Replies: 1
Views: 145
Posted By magmoormaster
Nah that's 2k+. Kapp's pre-2k volumizers are...

Nah that's 2k+. Kapp's pre-2k volumizers are longer than that.
Forum: Electronic and Mechanical 08-31-2019, 03:40 PM
Replies: 3
Views: 223
Posted By magmoormaster
If anyone would be willing to pick it up and ship...

If anyone would be willing to pick it up and ship it, I'd pay a finder's fee...
Forum: Autocockers 08-31-2019, 02:38 PM
Replies: 25
Views: 491
Posted By magmoormaster
It does. Like I said, it's a small part of many...

It does. Like I said, it's a small part of many factors. But it will make a difference.

If you look at a c-clipped 3-way, it uses the same shaft as a Belsales Hollowpoint 3-way, and thus the same...
Forum: WTB 08-31-2019, 12:44 PM
Replies: 9
Views: 309
Posted By magmoormaster
Hit up Apamburn, I know he had one at one point....

Hit up Apamburn, I know he had one at one point. He recently gave away a huge pile of random parts, and my guess is the trigger shoe was in there. But he might have taken it with him when he moved.
Forum: The Dead Zone 08-31-2019, 12:34 PM
Replies: 11
Views: 315
Posted By magmoormaster
Yeah, the DW barrels make things kind of hard. I...

Yeah, the DW barrels make things kind of hard. I have a pretty ridiculous insert collection (every size stainless insert ever made, .675 up to .697), which really limited the case options on its own....
Forum: Autocockers 08-31-2019, 12:27 PM
Replies: 25
Views: 491
Posted By magmoormaster
There's a lot that goes into it, including the...

There's a lot that goes into it, including the diameter of the input/output ports, the barb spacing, etc. A c-clipped brass 3-way uses 003 o-rings, but because of the barb spacing, it has a much...
Forum: Autocockers 08-30-2019, 09:46 PM
Replies: 25
Views: 491
Posted By magmoormaster
I agree with the argument about smoothness but 3...

I agree with the argument about smoothness but 3 o-ring designs definitely have a shorter switch length.
Forum: Autocockers 08-29-2019, 12:29 AM
Replies: 25
Views: 491
Posted By magmoormaster
I'm not a huge fan... I don't dislike them by any...

I'm not a huge fan... I don't dislike them by any means, but 99% of the time the added adjustment never gets touched. It adds more seals to go bad, and by this point they usually have. I won't rip...
Forum: Autocockers 08-28-2019, 11:49 AM
Replies: 25
Views: 526
Posted By magmoormaster
Yeah, with how inconsistent paint is these days,...

Yeah, with how inconsistent paint is these days, you often have to run a pretty substantial underbore to not get the occasional partial rollout.
Forum: The Dead Zone 08-28-2019, 11:36 AM
Replies: 45
Views: 963
Posted By magmoormaster
Two of my teammates have HK Army Shockers....

Two of my teammates have HK Army Shockers. Basically custom-milled RSX's. They're a bit more kicky than I would prefer, mostly because they're obscenely light. Otherwise they're solid guns....
Forum: The Dead Zone 08-27-2019, 06:33 PM
Replies: 45
Views: 963
Posted By magmoormaster
Bob Longs shoot really well, but they are not a...

Bob Longs shoot really well, but they are not a plug n play kind of gun. You need to be pretty meticulous with maintaining them. Supposedly the Insight is not nearly as bad as the VIS or G6r, since...
Forum: 3D Printing 08-27-2019, 06:24 PM
Replies: 3
Views: 117
Posted By magmoormaster
I tried and failed, mostly because my dad (who...

I tried and failed, mostly because my dad (who was doing all the work) was trying some weird ideas instead of what I told him to do. For as much time and effort you'd put into it, you might as well...
Forum: Ask The Experts 08-27-2019, 05:31 PM
Replies: 3
Views: 123
Posted By magmoormaster
The hole above the center would lead me to...

The hole above the center would lead me to believe it's an alternate plate, in case the user has ACT.
Forum: Autocockers 08-27-2019, 02:16 PM
Replies: 1
Views: 101
Posted By magmoormaster
While I can't confirm, I'm 99.9999% positive the...

While I can't confirm, I'm 99.9999% positive the answer is yes. Belsales and Eclipse parts are identical besides styling.
Showing results 1 to 40 of 400

 
Forum Jump

All times are GMT -4. The time now is 11:59 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO
© MCB Network LLC