Custom

[super_stanchy]

Originally Posted by nitsua

I see you're not doing threading services but I was curious if you had any bored barrels stocked? Looking to get an 8 or 11 inch Phantom thread.

yes i have polished silver 11" in stock

i will be doing a CCI order (goin to see mike after work) sometime next week as well

[tybalt762]

Would like to halfblock & mill a GX3 body, as well as freak bore an aluminum bull barrel.

When you halfblock, do you change out the internals, or do I need to grab those from CCM or somewhere?

[super_stanchy]

Originally Posted by tybalt762

Would like to halfblock & mill a GX3 body, as well as freak bore an aluminum bull barrel.

When you halfblock, do you change out the internals, or do I need to grab those from CCM or somewhere?

i will supply the bolt, sled and pin

i will shorten customer supplied pump/ram arms and slot your hammer

[ilivlife]

Can you make a stick feed adapter for a t2?

[super_stanchy]

Originally Posted by ilivlife

Can you make a stick feed adapter for a t2?

i made 1.... but it had some flaws, making another would be cool

need to figure out how to get a cci one to fit (or have mike make one with a smaller hole and slightly different location for it)

[drewkroeker]

I've got an idea for my stock matrix breeches. Could you seal the detent holes and then mill out a section for ego detents? These would then need some sort of cover to keep the detents in place.

This wouldn't have to be an immediate project. So far my only solution to double feeds has been to jump on any NDZ breeches that I see for sale, since these take impulse detents and can withstand the force of a halo.

Let me know if this is something you could help me with.

Thanks,

Drew

[DoC19K]

PM sent about redrilling and adjusting a nelson unibody to take autococker barrels. Its only pushing back the work about a half inch back closer to the body.

[super_stanchy]

Originally Posted by drewkroeker

I've got an idea for my stock matrix breeches. Could you seal the detent holes and then mill out a section for ego detents? These would then need some sort of cover to keep the detents in place.

This wouldn't have to be an immediate project. So far my only solution to double feeds has been to jump on any NDZ breeches that I see for sale, since these take impulse detents and can withstand the force of a halo.

Let me know if this is something you could help me with.

Thanks,

Drew

sounds doable, i know nothing about the old matrix stuff....
is the stock detent threaded? could it be possible to make a 2 piece detent that holds an ego detent instead?

Originally Posted by DoC19K

PM sent about redrilling and adjusting a nelson unibody to take autococker barrels. Its only pushing back the work about a half inch back closer to the body.

just saw the pm... havnt read it yet

sounds doable

[barkingspider]

I thought I would post this here since this is the way your keep track of work requests.

Cut length of armson barrel and AC Rethread. Armson tip threaded for spec ops c series tips.

I know you mention this being on your list of things to do, but I would love about 10 collars with male threading for the c series tips do I can glue on the front of other cf barrels I have

[super_stanchy]

Originally Posted by barkingspider

I thought I would post this here since this is the way your keep track of work requests.

Cut length of armson barrel and AC Rethread. Armson tip threaded for spec ops c series tips.

I know you mention this being on your list of things to do, but I would love about 10 collars with male threading for the c series tips do I can glue on the front of other cf barrels I have

rethreading starting aug 1st

collars.... i need to take my mic's to the pb shop and measure up some DW barrels and get some sizing.... then i can finish the programming

i've wanted to make em since they went on sale last spring... just havnt had a chance to do it