Limited run Freak boring Service Offered

tjd10684 · 06-27-2012, 05:37 PM

UPFRONT PRICING:
ALUMINUM = $35
STAINLESS = $65

I am looking to start freak boring in a limited run.

I am looking to get $35, includes return shipping (International shipping +$5)

I don't own every barrel so I can't guarantee I can bore every kind of barrel but if the od is relatively straight I should be able to. If for some reason I can't get it aligned I will send it back to you no charge.

I keep getting asked about quantity discounts so I am going to put my stock answer here. I am not offering quantity discounts here is why, to bore a barrel in my jig each one takes some time to setup and it does not get any faster doing the same barrel. So think of it this way I can do 10 different barrels in the same time it takes me to do 10 of the same barrel. Typically when you get a quantity discount its because of reduced setup time to do the same operation over and over since my setup is designed to be efficient at a wide range I can not setup any faster even if its the same barrel.

I am going put a standard response to a question I have been getting frequently. The question is the insert is sticking out the back of the barrel is this normal. The answer is Yes. I make sure that the insert sticks out the back of the barrel about 0.005-0.010. this is so make sure when you screw the barrel in the insert will not slide around. the reason DW barrels and freak barrels dont stick out is because they have orings to help keep the insert in place. When I bore the barrel their is rarely enough room to put an oring so I have to make sure it sticks out just a little to keep the insert still. Also their is no worry about hurting the insert unless your using a pipe wrench to tighten your barrel. The inserts are actually quite strong in that direction.

Here is a pic of what the insert should look like in the bored barrel.

I am now going to try my hand at some stainless barrels. The price for stainless barrels is going to be $65

Below is a list of barrel types that I know I can do I will update the list as I do more.

- CP one peice
- Spyder stock
- WGP stock
- Eclipse shaft 2
- Eclipse Shaft 3
- Eclipse Shaft 4
- Eclipse Solo
- CP 2 piece
- Bob Long Assault
- Lapco Big Shot
- Bob Long G6R stock
- Bob Long 2 piece
- Dye UL
- Evil Pipe (+5 for windows)
- Evil Driver
- Stock Rev-i (+10 for lots of windows)
- Stock Empire Traccer
- Stock G4
- Stock G5
- New style Karner backs
- Machine Vapor stock

Barrels I don't really want to do.

- Phantom barrels (too much possibility of error when removing the shank of the barrel before the threads.)
- A1 stock barrels (extremely thin after finished boring)
- JJ Edge (I do not believe these barrels are bored straight enough to freak bore in my jig.)
- Lapco tight stick (too thin and already nearly as small as freak inserts come I measured it at 0.6813)
Here is how payment works.

Process for shipping and payment.

1. PM Me for shipping/payment info
2. Send me your barrel (please fill out this form and include it with your barrel https://docs.google.com/spreadsheet/...9zTnc6MQ#gid=0)
3. I will bore it (turn around is currently 1 day)
4. I will inform you it is complete.
5. You send me payment.
6. I ship it back to you via USPS, unless otherwise agreed upon earlier.

Status

ACCEPTING NEW WORK
ALSO ACCEPTING STAINLESS

Please leave me feedback to let others know I'm not just some flaky dude in a garage.

tjd10684 · 08-08-2012, 09:54 PM

I thought I might show off my freak boring jig so you know I'm not just some flaky dude in a garage. well I am in a garage.... But I'm not flaky

.

tjd10684 · 08-12-2012, 09:37 AM

boring one if my sterling barrels

MorueM · 08-12-2012, 04:05 PM

What size is that reamer?

ryanhall41 · 08-12-2012, 07:53 PM

can you do stainless barrels?

joedirt199 · 08-12-2012, 08:41 PM

looking good. will definately help take a load off stanchy. just watch what you're getting yourself into. people love their freak inserts and have lots of barrels.

tjd10684 · 08-12-2012, 11:02 PM

Quote:

Originally Posted by MorueM

What size is that reamer?

The right size

0.745

Quote:

Originally Posted by ryanhall41

can you do stainless barrels?

I don't really want to they take much much longer to bore than aluminum, and they are much harder on my tools. But for the right price I might be willing to try a few. If I had to put a price on trying it 50 would get me to try it.

Quote:

Originally Posted by joedirt199

looking good. will definately help take a load off stanchy. just watch what you're getting yourself into. people love their freak inserts and have lots of barrels.

Thats kinda what I am counting on

but I know I can't do quite the volume SSC does I really like to keep my lead times short if I get backed up more than 2 days I will quit taking new work until I am caught up. Right now 8/12/12 I am boring barrels the same day they come in and shipping out the next day.

Waylost · 08-13-2012, 12:10 PM

This just landed in my mailbox today.

One word, "Legen wait for it......Dary!"

Thanks for the help Tom

tjd10684 · 08-13-2012, 12:35 PM

no problem hope it works well for you. I was just going to message you to see if you got it yet.

KPCS · 08-15-2012, 09:16 PM

A man that know what he's doing

What no O-ring grooves ?? j/k

Great job.

Ken W

06-27-2012, 05:37 PM	#1 (permalink)
tjd10684 MCB Member Join Date: Jul 2009 Location: Beaver Falls PA (outside Pittsburgh)	Limited run Freak boring Service Offered UPFRONT PRICING: ALUMINUM = $35 STAINLESS = $65 I am looking to start freak boring in a limited run. I am looking to get $35, includes return shipping (International shipping +$5) I don't own every barrel so I can't guarantee I can bore every kind of barrel but if the od is relatively straight I should be able to. If for some reason I can't get it aligned I will send it back to you no charge. I keep getting asked about quantity discounts so I am going to put my stock answer here. I am not offering quantity discounts here is why, to bore a barrel in my jig each one takes some time to setup and it does not get any faster doing the same barrel. So think of it this way I can do 10 different barrels in the same time it takes me to do 10 of the same barrel. Typically when you get a quantity discount its because of reduced setup time to do the same operation over and over since my setup is designed to be efficient at a wide range I can not setup any faster even if its the same barrel. I am going put a standard response to a question I have been getting frequently. The question is the insert is sticking out the back of the barrel is this normal. The answer is Yes. I make sure that the insert sticks out the back of the barrel about 0.005-0.010. this is so make sure when you screw the barrel in the insert will not slide around. the reason DW barrels and freak barrels dont stick out is because they have orings to help keep the insert in place. When I bore the barrel their is rarely enough room to put an oring so I have to make sure it sticks out just a little to keep the insert still. Also their is no worry about hurting the insert unless your using a pipe wrench to tighten your barrel. The inserts are actually quite strong in that direction. Here is a pic of what the insert should look like in the bored barrel. I am now going to try my hand at some stainless barrels. The price for stainless barrels is going to be $65 Below is a list of barrel types that I know I can do I will update the list as I do more. - CP one peice - Spyder stock - WGP stock - Eclipse shaft 2 - Eclipse Shaft 3 - Eclipse Shaft 4 - Eclipse Solo - CP 2 piece - Bob Long Assault - Lapco Big Shot - Bob Long G6R stock - Bob Long 2 piece - Dye UL - Evil Pipe (+5 for windows) - Evil Driver - Stock Rev-i (+10 for lots of windows) - Stock Empire Traccer - Stock G4 - Stock G5 - New style Karner backs - Machine Vapor stock Barrels I don't really want to do. - Phantom barrels (too much possibility of error when removing the shank of the barrel before the threads.) - A1 stock barrels (extremely thin after finished boring) - JJ Edge (I do not believe these barrels are bored straight enough to freak bore in my jig.) - Lapco tight stick (too thin and already nearly as small as freak inserts come I measured it at 0.6813) Here is how payment works. Process for shipping and payment. 1. PM Me for shipping/payment info 2. Send me your barrel (please fill out this form and include it with your barrel https://docs.google.com/spreadsheet/...9zTnc6MQ#gid=0) 3. I will bore it (turn around is currently 1 day) 4. I will inform you it is complete. 5. You send me payment. 6. I ship it back to you via USPS, unless otherwise agreed upon earlier. Status ACCEPTING NEW WORK ALSO ACCEPTING STAINLESS Please leave me feedback to let others know I'm not just some flaky dude in a garage. __________________ My Feedback - http://www.mcarterbrown.com/forums/f...ml#post1575817 I also freak bore http://www.mcarterbrown.com/forums/a...ml#post2393405 A wise man once said: "The gap between theory and reality is not as far in theory as it is in reality." Last edited by tjd10684; 02-01-2013 at 07:12 PM.

08-08-2012, 09:54 PM	#2 (permalink)
tjd10684 MCB Member Join Date: Jul 2009 Location: Beaver Falls PA (outside Pittsburgh)	I thought I might show off my freak boring jig so you know I'm not just some flaky dude in a garage. well I am in a garage.... But I'm not flaky. __________________ My Feedback - http://www.mcarterbrown.com/forums/f...ml#post1575817 I also freak bore http://www.mcarterbrown.com/forums/a...ml#post2393405 A wise man once said: "The gap between theory and reality is not as far in theory as it is in reality."

08-12-2012, 09:37 AM	#3 (permalink)
tjd10684 MCB Member Join Date: Jul 2009 Location: Beaver Falls PA (outside Pittsburgh)	boring one if my sterling barrels __________________ My Feedback - http://www.mcarterbrown.com/forums/f...ml#post1575817 I also freak bore http://www.mcarterbrown.com/forums/a...ml#post2393405 A wise man once said: "The gap between theory and reality is not as far in theory as it is in reality." Last edited by tjd10684; 08-12-2012 at 09:42 AM.

08-12-2012, 04:05 PM	#4 (permalink)
MorueM Active Member Join Date: Mar 2008	What size is that reamer? __________________ Feedbacks Looking for: BPS Reflex parts

08-12-2012, 07:53 PM	#5 (permalink)
ryanhall41 Active Member Join Date: Jul 2010	can you do stainless barrels? __________________ Jackal RDL, Works autocoker, Dragon Timmy, Dye dm3 F/S/T WTB Eclipse F1 cocker or any undrilled eclipse bodies Pbn feedback customcockers feedback Mcb feedback

08-12-2012, 08:41 PM	#6 (permalink)
joedirt199 ur my sister Join Date: Apr 2009 Location: St Louis	looking good. will definately help take a load off stanchy. just watch what you're getting yourself into. people love their freak inserts and have lots of barrels. __________________ God created Police so Firemen would have HEROES In God we trust, everyone else gets searched 9mm will make you weak! MY FEEDBACK http://www.mcarterbrown.com/forums/f...-feedback.html CCM Works Sniper, Thumper, Kingman Hammer Low Pressure with Vertical ASA, TPX, Ion mech/closed bolt

08-13-2012, 12:35 PM	#9 (permalink)
tjd10684 MCB Member Join Date: Jul 2009 Location: Beaver Falls PA (outside Pittsburgh)	no problem hope it works well for you. I was just going to message you to see if you got it yet. __________________ My Feedback - http://www.mcarterbrown.com/forums/f...ml#post1575817 I also freak bore http://www.mcarterbrown.com/forums/a...ml#post2393405 A wise man once said: "The gap between theory and reality is not as far in theory as it is in reality." Last edited by tjd10684; 08-13-2012 at 12:50 PM.

08-15-2012, 09:16 PM	#10 (permalink)
KPCS Machinist Join Date: Apr 2006 Location: Michigan	A man that know what he's doing What no O-ring grooves ?? j/k Great job. Ken W __________________ KPCS http://www.facebook.com/KPCSpb?ref=hl I'm just a glorified drill press operator. I have come here to chew bubblegum & kick @$$ and I'm all out of bubblegum ...... http://www.youtube.com/watch?v=1jPG_JEyt-M

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search