-   CCI (
-   -   Consolidating Efficiency..? (

artguy63 05-12-2012 01:21 AM

Consolidating Efficiency..?
I'm not sure if there already is a thread out there that covers this. If there is, mod (cough cough CJ) please delete.

So, with all the various upgrades and accessories that people can put on their Phantoms, I have seen multiple threads on how people are running them, their opinions, etc etc. Rather than searching through multiple threads, I figured perhaps we could start a consolidated thread where people can see the set up and numbers that people are getting.

For example, I'll start.

VSC Phantom
- ASP Roundhead body
- Deadlywind barrel with full freak kit
- 3.5 oz tank
- (soon to have bobbed and gauged valve)
- stock internals
- CCI O-ring TPC
- stock springing

I'm averaging about 250ish shots out of a single fill. This is on days that are about 65-75 degrees, and also before the valve work.

BassDude 05-12-2012 02:07 AM

Not a bad idea. Here's mine. They are only the upgrades pertaining to efficiency and consistency with 12ies.

ASP Detent Modded Body
Deadlywind barrel
SSC Tri Fluted Hammer
Polished Internals
Red Main Spring, Stock Valve Spring
ASP O-Ringed Ported Open Faced TPC
Palmer's Sideline Stabilizer set at 500 PSI

On a test with 20 seconds between each shot, I got 38 shots before drop off occurred with an average of 276 fps. Almost all shots were +/- 5.

esparzar 05-12-2012 02:21 AM

14" Deadly Wind Barrel
Stock Internals
Bobbed & Gauged Valve
04' Dye Hyper Reg set at 750ish psi
drop forward macro line and hardline kit with a 13/3000 tank
Fps sitting around 270

76* degree weather and 100% humidity standard shooting averaging around 150 shots plus 3 dry fires.

808Jackal 05-12-2012 08:27 AM

Nice idea

Phantom #5
ASP Roundhead with detents
Dye ultralight back SSC freak bored 14' carter whoosh tip
SSC tri fluted hammer
Stock TPC
Red main spring Yellow valve
Punishers customs bobbed and gauged valve
HSC bottom line 6 .5 inch steel braided hose + QD
Georgia gunsmithing dry film lubricant on internals

76-80* avg weather
Standard to fast shooting at 280 fps and below
38+ shots off a 12 gram

Halo 05-13-2012 08:21 AM

Stock CCI body (added teflon tape to both feed block and front grip frame screw)
Trracer BBA
Azodin Regulator screwed into BBA set to around 490 PSI
11" barrel bored for Freak inserts
Polished Stock Bolt
Polished stock hammer
Stock Power Tube
Red Maddman Spring as main
Very light valve spring (non-standard, but similar to or lighter than Autococker sear spring)
HSC bottom line with macro line running to reg.

Velocity set to an average of 275 FPS
25-27 degrees Celcius (77-80 f)
about 5 seconds between shots (the time it takes me to put everything down, write down FPS values and then shoot again.)
42 shots at set velocity + two shots below ( 250, 220, vent)

Recently acquired a SSC fluted hammer and am experimenting with increased post reg valve volume as I've found that current valve volume might be starving the marker at sub 600 PSI pressures. Preliminary testing is proving positive. I'll update this when I've redone efficiency testing.

Dr. VonDeafingson 05-16-2012 09:58 AM

I'll get some numbers this weekend and edit this post when I do. You should ask Tim to get numbers on his stab valve phantom.

Good idea, Alex.

Phantom_Dave 05-17-2012 12:19 PM

Stock internals
Red Main spring
CP Reg - Set to 500psi ~
Freak barrel
13/3k bottle on a ASA
275 fps -/+ 5

150-160~ in game, if i was careful and slowly fired off one at time may get 175
This setup is very consistant, only change is check freak insert in the afternoon. Usually changes 1 or 2 sizes.

Scharfschutze91 05-17-2012 01:02 PM

freak bored 12 inch barrel
asp ported tpc
red main spring

shooting around 280 +/- 5ish
90* weather + 80% humidity

I get around 42 good shots from a crossman 12 gram.

p-bpat 05-17-2012 01:20 PM

Vsc duckslide phantom
Duckslide (I only mention this because it covers the barrel porting)
6 inch ssc freak bored barrel
stock cci internals (lightly polished)
red main and stock valve springs
hardline front vert to valve

I get a good 35 shots out of it right now (warm, outdoors) at approximately 270 fps, but when I turn it down to indoor speeds (250) I get around 38 shots.
I am getting a ssc fluted hammer and will post again with the new info and more accurate information.

funsi00 05-17-2012 10:04 PM

VSC with Palmer phantom stab set at 500PSI
Silver valve spring, Blue main spring
8 inch CCI barrel bored for Ifit inserts
Stainless steel braided airline
New oring TPC, stock internals
outdoor velocity 279,279,280 over chrono
Insert match paint, not underboring
160 shots on 1 oz of CO2 from 3.5oz tank.

All times are GMT -4. The time now is 04:15 PM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO
© MCB Network LLC