mcarterbrown.com  

CCM Chipley Machine

Reply
 
Thread Tools Search this Thread
Old 02-17-2012, 09:16 AM   #1 (permalink)
Newbie
 
Join Date: Apr 2011
Location: fridley, minnesota

your dye rotor on t2 has any issue?


i used dye rotor hopper on my t2. i noticed that i had more chopping paint on t2. i used same dye rotor hopper on my geo2 without any issue. fyi, i've used proto primo loader on t2 then i seems have less chopping paints but not perfect yet.

i wonder if you have used dye rotor hopper on your t2 without chopping paints issue?

did i get wrong size feedneck for my dye rotor because it is too short?

btw, three different people had suggested the same advice that i should have used the viewloader revolution c.a.t. without forcing to feed the paints. i assume it has nothing to do with feedback, right?

then why geo2 could achieve with dye rotor that t2 could not achieve with dye rotor on mine?
buzzdragon is offline   Reply With Quote
Old 02-17-2012, 09:18 AM   #2 (permalink)
MCB Member
 
mrmag11's Avatar
 
Join Date: Feb 2009
Location: Columbus, GA

Never chopped or double fed on my T2, but my J2L double feeds all the time.
__________________
MCB Feedback

World of Tanks Profile

Quote:
Originally Posted by CCM CHICK View Post
I say to you with love in my heart... your a whore.
Quote:
Originally Posted by Scharfschutze91 View Post
i like the zipper... pullover's hurt when i take them off. I gel my hair everyday so when I pull it off it snags on my hair and hurts.
mrmag11 is offline   Reply With Quote
Old 02-17-2012, 09:32 AM   #3 (permalink)
Newbie++
 
noclue119's Avatar
 
Join Date: Apr 2009
Location: Atlanta, GA

CCM Fan
I stopped using force fed hoppers on my pumps. I had a few issues with both my Rotors and Halo B. The problem were mainly due to small bore paint or soft shell paint. The problem I experience was that the ball stack was pushed so far down(by the force fed tension), that there was a good chance of the bolt slicing the next ball. That is why if you notice Eclipse bolts have that ramp on top. It does seem to eliminate a lot of the slicing issue.

Either way, it cause enough of a problem for me to switch over to Sportshort/Winchester/Revvy. If you pick out your paint carefully(hard shell and decent size) I think you are fine with a rotor.


BTW You can turn down the tension on your rotor. This will help too.
http://www.youtube.com/watch?v=yw0nE9qtOIc
__________________
"Originally posted by Element Paintball@pbnation: you realize it would be easier to get a new wife than a new dc2."



My MCB Feedback

Last edited by noclue119; 02-17-2012 at 09:41 AM.
noclue119 is offline   Reply With Quote
Old 02-17-2012, 09:35 AM   #4 (permalink)
The cries of the carrots
 
Hogzilla88's Avatar
 
Join Date: May 2011
Location: Arlington, Tx

CCM Fan
I've used my prophecy on my s6.5 with no issues.
Hogzilla88 is offline   Reply With Quote
Old 02-17-2012, 09:37 AM   #5 (permalink)
Yield and Overcome...
 
Dr. PhunkyPants's Avatar
 
Join Date: Apr 2008

CCM Fan
I guess the main question I'd have is whether you handle the pump stroke on the T2 differently.

User technique is going to have a big impact on likelihood of double feeds!
Dr. PhunkyPants is offline   Reply With Quote
Old 02-17-2012, 09:41 AM   #6 (permalink)
Active Member
 
Neurosis's Avatar
 
Join Date: Sep 2010

CCM Fan
U can lower the springtension on your rotor to the minimum, there must be a small screw. This will help a little bit, but when I used a Rotor on my T2 there was the same problem. Best Hopper at the moment to use on a T2 is definatly a Sportshot, Primo or Revo.

Ps. Damn to slow ^^
__________________
TEAM PUMPZILLA
www.pumpdays.de <- Check out the German PumpPotal
-> My CCM T2
-> My CCM S6
-> My whole family
Neurosis is offline   Reply With Quote
Old 02-17-2012, 09:42 AM   #7 (permalink)
Serving Tea for CCM
 
senghing27's Avatar
 
Join Date: Nov 2007
Location: Virginia
Send a message via AIM to senghing27

CCM Fan
Brass N Wood Fan
Palmers Fan
When I had the rotor mounted on my J2L, I had no problems.
Then again, I'm not using the Nopro feedneck. It might be because of ball stack, but at the end of the day... the rotor is overkill.

Forcefeed hoppers on a pump is super overkill IMO. Yes, you have pressure and for sure a ball ready to go... But I'd rather run a sportshot/revvy/primo than deal with the headaches and increased hopper weight.

I've seen one person in action that actually makes great use of the rotor and that is Carter. Nothing like tennis elbow autotriggering.
__________________
Quote:
Originally Posted by russc View Post
Senghing, you are the happiest paintballer ever.
~My Feedback~
senghing27 is offline   Reply With Quote
Old 02-17-2012, 09:47 AM   #8 (permalink)
Newbie++
 
noclue119's Avatar
 
Join Date: Apr 2009
Location: Atlanta, GA

CCM Fan
Quote:
Originally Posted by Neurosis View Post
U can lower the springtension on your rotor to the minimum, there must be a small screw. This will help a little bit, but when I used a Rotor on my T2 there was the same problem. Best Hopper at the moment to use on a T2 is definatly a Sportshot, Primo or Revo.

Ps. Damn to slow ^^
hehe. I think u posted at the same time I did. I had to edit my post to add the video.
__________________
"Originally posted by Element Paintball@pbnation: you realize it would be easier to get a new wife than a new dc2."



My MCB Feedback
noclue119 is offline   Reply With Quote
Old 02-17-2012, 10:36 AM   #9 (permalink)
Formerly lancecst
 
BLachance75's Avatar
 
Join Date: Sep 2006
Location: Western Mass

CCM Fan
I use a rotor on my T2 with no issues. Are you sizing your paint well so that you aren't getting partial rollouts. If you have a partial rollout the next ball could be enteric the breech enough that the bolt slices it.
__________________
BLachance75 is offline   Reply With Quote
Old 02-17-2012, 12:49 PM   #10 (permalink)
Newbie
 
Join Date: Apr 2011
Location: fridley, minnesota

thank everyone for advice. video helps me too so i will try that one too on the tension.

back to lancest,
wow, you are only one has no issues. ok, let me ask you a question before i am in right direction to do some test on sizing. is your paint brittle like tournament grade paints or cheap paints (hard shell and decent size) for rental gun. i used tournament grade paints.

Quote:
Originally Posted by lancecst View Post
I use a rotor on my T2 with no issues. Are you sizing your paint well so that you aren't getting partial rollouts. If you have a partial rollout the next ball could be enteric the breech enough that the bolt slices it.
buzzdragon is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » CCM

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 09:46 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC