my pimple, many pics

K_Obeastly · 05-19-2008, 09:50 PM

I finally got it done last week or so and am now getting around to getting photos up.

one with its brother

Somewhere along the line I decided to make it as big as I could while not going overboard. This pic was for a size comparison but it doesn't really do the job all that well.

For those wanting to see inside

brass sleeve and epoxied air port to cut off the air to the solenoid and provide a good surface for the pump rod.

pump handle, back block and one end of the pump rod.

as they would be assembled w/ the bolt.

new hammer, spring and modded ram body. I had to open up one end of the ram for the hammer to slide freely and rounded the other end so it could be covered by the back block. The hammer is currently two pieces but they are comming seperated so I'll have to make a new one sometime soon.

changes to the valve to accomadate the pump guide rod

guide rod/volumizer assembled

sear, trigger, grip frame, milled slot w/ ignored sharpie lines and such

then the good stuff.
I made a request to someone and hoped to see some crappy jewels but instead got almost unusable crappy stickers and made due the best I could (within reason of course, and they were free so I can't complain too much.)

russc · 05-19-2008, 09:56 PM

That's brilliant! Nice job!

Harbinger[TG] · 05-19-2008, 10:13 PM

Good stuff. Clean lines.

sparky · 05-20-2008, 12:26 AM

That acually looks really good. Finally a nice looking SP marker

BigOldSkool · 05-20-2008, 12:42 PM

Ha!!! That may be the best use of an Impulse yet...

Welcome to the club of confusing *** pump guns

05-19-2008, 09:50 PM	#1 (permalink)
K_Obeastly Seasoned Member Join Date: Jul 2006 Posts: 599	my pimple, many pics I finally got it done last week or so and am now getting around to getting photos up. one with its brother Somewhere along the line I decided to make it as big as I could while not going overboard. This pic was for a size comparison but it doesn't really do the job all that well. For those wanting to see inside brass sleeve and epoxied air port to cut off the air to the solenoid and provide a good surface for the pump rod. pump handle, back block and one end of the pump rod. as they would be assembled w/ the bolt. new hammer, spring and modded ram body. I had to open up one end of the ram for the hammer to slide freely and rounded the other end so it could be covered by the back block. The hammer is currently two pieces but they are comming seperated so I'll have to make a new one sometime soon. changes to the valve to accomadate the pump guide rod guide rod/volumizer assembled sear, trigger, grip frame, milled slot w/ ignored sharpie lines and such then the good stuff. I made a request to someone and hoped to see some crappy jewels but instead got almost unusable crappy stickers and made due the best I could (within reason of course, and they were free so I can't complain too much.) __________________ I b da fat one http://www.youtube.com/watch?v=oERRPtEf8EM Glen Benton: doing more to convert me to christianity by 6 A.M. than most christians do all day.

05-19-2008, 09:56 PM	#2 (permalink)
russc Newbie Join Date: Apr 2006 Location: Vancouver, BC Posts: 4,106	That's brilliant! Nice job! __________________ YouTube Channel / Raincouver! / Gallery / Feedback / Blackleaf Outfitters -Russ

05-20-2008, 12:42 PM	#5 (permalink)
BigOldSkool MCB Member Join Date: Jul 2006 Location: Deer Park, NY Posts: 1,729	Ha!!! That may be the best use of an Impulse yet... Welcome to the club of confusing * pump guns __________________ RIP - Ed "BigDaddy" Roth and "Indian" Larry "Reading APG does not make you an airtech"** http://www.myspace.com/eastcoastanarchypaintball

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search