FSDO

p8ntninja · 03-14-2011, 12:08 AM

What could be causing this?? I'm shooting a Clone sans VX internals with my dwell set at 11 and abs at 4ms. Only has about a case and a half shot through it. I mainly noticed the FSDO when my dwell was at 10 and abs was off. Was my dwell too low? Reg not fully broken in? Any help/info is appreciated!

WebFisher · 03-14-2011, 08:13 AM

Most of the time, FSDO in the Clone is caused by a sticking drive train. Clean and relubricate the drivetrain with Militia Lube (remember, the o-rings only need to look wet). If you continue to have problems:
-increase the dwell by 1-2 ms.
-increase the ABS parameter on your board.

p8ntninja · 03-14-2011, 09:51 PM

Thanks Web for the heads up, I'll make sure to check and do so if necessary this weekend

thcgunsmoke · 03-16-2011, 11:01 AM

lube is a huge factor to how the clone preforms, from the factory macdev done a heavy lube job so that it gets into all the spots it neesd to.

militia lube should go on transparent you should see no whiteness at all, and a very very thin amout needs to be applied,

if its cold / cool out up the dwell to 14, if your still having issues up the abs

Tek2974 · 03-24-2011, 09:26 AM

try turning your reg up a little, I was compensating w/ abs to get my velocity up to 280, but first shot was around 220 and would sometimes just chuff out the end of the barrel, turned the reg up a tad and reset my dwell and abs and have no problems.

p8ntninja · 05-16-2011, 10:02 PM

Was able to get back out this weekend finally, (finances have not been the greatest as of late) wiped all factory lube off and relubed the night before and all of the FSDO disappeared, shot like a dream! Thanks, Guys for all the tips!

03-14-2011, 12:08 AM	#1 (permalink)
p8ntninja MCB Member Join Date: Dec 2010 Location: Originally SoCal, currently Midway Utah	FSDO What could be causing this?? I'm shooting a Clone sans VX internals with my dwell set at 11 and abs at 4ms. Only has about a case and a half shot through it. I mainly noticed the FSDO when my dwell was at 10 and abs was off. Was my dwell too low? Reg not fully broken in? Any help/info is appreciated!

03-24-2011, 09:26 AM	#5 (permalink)
Tek2974 Rocking the casbah Join Date: Jun 2010 Location: Lehighton, PA	try turning your reg up a little, I was compensating w/ abs to get my velocity up to 280, but first shot was around 220 and would sometimes just chuff out the end of the barrel, turned the reg up a tad and reset my dwell and abs and have no problems. __________________ MCB Feedback Lead me, follow me, or get out of my way. 10th Line

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

03-14-2011, 09:51 PM	#3 (permalink)
p8ntninja MCB Member Join Date: Dec 2010 Location: Originally SoCal, currently Midway Utah	Thanks Web for the heads up, I'll make sure to check and do so if necessary this weekend

03-16-2011, 11:01 AM	#4 (permalink)
thcgunsmoke Newbie Join Date: Oct 2010	lube is a huge factor to how the clone preforms, from the factory macdev done a heavy lube job so that it gets into all the spots it neesd to. militia lube should go on transparent you should see no whiteness at all, and a very very thin amout needs to be applied, if its cold / cool out up the dwell to 14, if your still having issues up the abs

05-16-2011, 10:02 PM	#6 (permalink)
p8ntninja MCB Member Join Date: Dec 2010 Location: Originally SoCal, currently Midway Utah	Was able to get back out this weekend finally, (finances have not been the greatest as of late) wiped all factory lube off and relubed the night before and all of the FSDO disappeared, shot like a dream! Thanks, Guys for all the tips!