What did you 3D print today?

[RAZRBAKK]

My new XB was missing one of the plungers on the rear seats to lay them down.





Original:

[chops]

Marker Stands. I also designed a quick one for a VSC phantom since it doesn't have an ASA. STL here

[Brandon]

nice job, printing it now!!

[antifat]

I made a chrono trap so I don't have to drive out to my parents house to test velocity, the printed parts are just the center hole fill and the cradles.

[goofyman23]

Didn't have an ASA adapter so whipped this up in Fusion and printed in ABS.

Neon green is all I had 😆

[chops]

Muffler adapter for dry firing. Fits Stella or Empire sniper/ressy barrel backs and 1/2" pneumatic silencers.

https://www.thingiverse.com/thing:6669083

[Alexndl]

Where did you buy the muffler?
Is it a SMC?

[chops]

Alexndl yep it’s a SMC ANA1-04. I bought one here: https://www.ebay.com/itm/353319192969

[Budster]

been working all this tipx shroud and angled foregrip for awhile now. works good in the field. still gotta play with the tpu holo sight some more though. printed the buttstock out of tpu also

[Budster]

i designed and printed this stuff too. smaller hopper to hold about 75 balls. empire sniper pump handle. new hand grips. 518 rubber ducky on mask! thanks for looking

[pghp8ntballer]

Captain Rex

[Brandon]

thinking of getting one of these for my Son when they go on sale again. A1 Mini, do you like it ?

[pghp8ntballer]

Brandon I absolutely love it. My only complaint is it’s so good that I wish I had a bigger bed. I have other printers and can print bigger, but the Bambu printers are just leaps and bounds better. But honestly at least 75% of all my prints fit on the Mini. 20+% would fit on the larger A1 or other Bambu’s and less than 5% of what I want to print would require a bigger bed than the other Bambu’s.
I’m holding out buying a P1S because I’m hoping they come out with a 350mm cubed or close printer or a tool changer.

[Lane]

Needed a bracket to hold some electronics and a pulley and stand for a stepper motor. Running a passivation test on laser engraved stainless steel. It drops the parts in the water for an hour, then lifts them out for an hour. Repeat for 24 hours.

[Frmrspec]

https://youtube.com/shorts/mpUcpTu87..._a87DgHkvIKTXl

modeled up and printed some CCM mags.. at $35 a pop, it’s a tough sell when I can make them for about $1 or so… same size as CCM’s mags but hold 1-2 extra rounds. Printed it laying flat with the internal radius facing up with zero supports.. came off the print bed ready to use.

the cap that retains the spring needs a hair of fine tuning but that’s easy peasy.

[crazedloon]

new larger, higher quality printer gave me a chance to model up something new.

[quillcrest]

Impressive! What is the lever pinion actually operating? I've struggled myself to design something that operates the bolt without doing any machining to the bolt itself.

[crazedloon]

The bolt is attached to a “sled” which has the rack on bottom allowing the pinion to slide the bolt through the action. To ensure the hammer does not interfere with the action it also slides along the top of the sled and the sled acts as a mechanical limit to the back stroke preventing overly long stroke with the lever.

[Chemical-x.....ahain]

I love it.

I have an affinity for levers, if I can be of assistance please let me know. Fwiw I've got printers sitting idle right now.

[nuclear zombie]

Designed and printed a magfed marker stand for my emf100.

[RAZRBAKK]

Pickup rings for a little custom work. I'll do a write up when it's wired up and working.

[Chemical-x.....ahain]

Almost there

[Alexndl]

Wow!
Good work!

[Cal440]

Nice I hope these will be available?

[BrickHaus]

These are Hella nice!