mcarterbrown.com

mcarterbrown.com (https://www.mcarterbrown.com/forums/)
-   Dealers Forum (https://www.mcarterbrown.com/forums/dealers-forum/)
-   -   SLPS kit, Cocker parts and hose, Macroline (https://www.mcarterbrown.com/forums/dealers-forum/255801-slps-kit-cocker-parts-hose-macroline.html)

maggot 04-30-2014 09:15 AM

SLPS kit, Cocker parts and hose, Macroline
 
PM me to ask about combined shipping savings when buying multiple items.

-----------------------------------------------------------------------------------------

Super Light Pump Stroke (SLPS) spring kits. These lightened springs will reduce the amount of force needed to re-cock your pump or Autococker and will improve the trigger pull. A lighter pump stroke means more accurate follow up shots. These springs are significantly softer than any of the springs found in the other spring kits.
How do they work? The key to the system is the lightened valve spring. A lighter valve spring means less force is necessary to push the valve open and release the same amount of air. Since less force is needed, you can also use a lighter hammer spring which makes the marker easier to re-cock.
You no longer need to purchase an expensive set of new internals to lighten your pump stroke. During my testing the biggest gains resulted on markers using stock WGP internals! Markers using stock internals had 20% to 25% reductions in the force needed to re-cock.


What is included:Replacement valve, hammer, sear, and slider trigger return springs. You need an Autococker valve tool to install the kit.

Installation: Install the SLPS valve and hammer spring. Sweet-spot your regulator (google this if you are unsure how to do it - it's very easy). If you are unable to achieve the desired FPS using the SLPS hammer spring, re-install the stock hammer spring and you'll find the IVG doesn't need turned in as far.
Replace the sear spring on your trigger frame with the SLPS sear spring. If you have a slider trigger frame, install the trigger return spring (trimmed end in first), trim off small pieces of the spring until you have the trigger pull desired.
These springs will NOT work on Empire Snipers or Trilogy series Autocockers.
$12 shipped (I will ship overseas, PM me for a quote).
https://mcarterbrown.com/pbimages/SLPS_Small.jpg


---------------------------------------------------------------------------------------------------------------------------------------


Autococker Parts Kit. This is an Autococker parts kit that every Cocker owner should have. The following is included (everything pictured):
1x complete Autococker o-ring rebuild kit
1 sear pin to hold your sear in place
1 improved hex-head stainless vertical ASA screw
1 valve jam nut
1 valve guide screw
4x set screws for timing rods (2 each of the two different sizes)
1x beavertail washer
8x trigger frame and beavertail screws (4 in stainless and 4 in black)
1 foot section of high quality black pneumatic hose - max pressure of 250 psi (more than twice the working pressure of an Autococker)
$18 shipped (I will ship overseas, PM me for a quote).
https://mcarterbrown.com/pbimages/Sm...ckerParts3.jpg


---------------------------------------------------------------------------------------------------------------------------------------


Autococker Hose Kit. A total of 12 feet of high quality pneumatic hose with a max pressure of 250 psi (more than twice the working pressure of an Autococker).
Choose any combo from the following colors: clear, black, yellow, blue, red, green, ice blue, ice green, ice red, ice yellow
$12 shipped (I will ship overseas, PM me for a quote).
https://mcarterbrown.com/pbimages/Small_HoseKits.jpg


---------------------------------------------------------------------------------------------------------------------------------------


Macroline Hose Kits. This is for continuous, uncut (not in 1 foot sections) Macroline. This is a nice glossy OEM-quality Nylon hose without any wording written on it. Available in BLACK or CLEAR (not clear like glass, please see pics).

This line is rated to 920 PSI working pressure. Do not fall for the cheap stuff other sellers have, that junk is usually rated BELOW the working pressure of your gun and can BURST! Additionally, that soft stuff they sell has a smaller inner diameter and less flow than this OEM quality Macroline. All of the fancy looking colored line is NOT rated for paintball pressures of 800psi.

Pro-tip: Use a razor blade to cut the needed portion off – less waste than 1 foot sections. Use some fine grit sandpaper to round off the sharp edge after cutting then apply a drop of paintball oil to the hose before putting it in the fitting, this will prolong the life off the o-ring inside your fitting and reduce the chance of it springing a leak!
10 feet = $14 shipped
25 feet = $24 shipped
(I will ship overseas, PM me for a quote).
https://mcarterbrown.com/pbimages/Small_DSCF2946.jpg
https://mcarterbrown.com/pbimages/Small_DSCF2947.jpg


---------------------------------------------------------------------------------------------------------------------------------------


Universal Screw Kit. These are high quality YFS screws in both stainless and black. Great for cockers and mags, but will also be useful for all markers. Includes: 4x ASA screws, 4x ASA plugs, 4x beavertail screws, 4x trigger frame screws, and 6x grip screws in two different thread sizes. A total of 96 screws!
$24 shipped (I will ship overseas, PM me for a quote).
https://mcarterbrown.com/pbimages/Sm...rsalScrews.jpg


---------------------------------------------------------------------------------------------------------------------------------------


ASA Screw Kit. These are high quality YFS screws in both stainless and black. Includes: 4x ASA screws and 4x ASA plugs. A total of 40 screws!
$15 shipped (I will ship overseas, PM me for a quote).
https://mcarterbrown.com/pbimages/Small_ASAScrews.jpg



---------------------------------------------------------------------------------------------------------------------------------------


Grip Screw Kit. These are high quality YFS screws in both stainless and black. Includes: 6x grip screws in two different thread sizes. A total of 48 screws!
$14 shipped (I will ship overseas, PM me for a quote).
https://mcarterbrown.com/pbimages/Small_GripScrews.jpg

Samhouston123 04-30-2014 05:33 PM

pmed

maggot 05-14-2014 09:07 AM

Back to the front page

maggot 05-27-2014 12:29 PM

bump!

maggot 06-16-2014 01:29 PM

bump!

maggot 07-17-2014 11:28 PM

bump!

honculada 07-19-2014 09:12 PM

I'll take a 2 slps spring kit.

maggot 07-25-2014 12:01 AM

Cocker kits now come with an improved stainless hex-head vertical ASA screw.
SLPS kits now come with a sear spring and a slider trigger return spring.

SOGAmember666 07-27-2014 06:42 PM

Do you by chance or will by chance have a o-ring kit for a CCM S6.5?

maggot 07-27-2014 06:50 PM

Quote:

Originally Posted by SOGAmember666 (Post 2997885)
Do you by chance or will by chance have a o-ring kit for a CCM S6.5?

No, but it's likely most/all of the ones you'd need are in the cocker kit that I sell. I don't sell the o-rings separate from the kit.


All times are GMT -4. The time now is 09:03 AM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO
© MCB Network LLC