mcarterbrown.com  

Reply
 
Thread Tools Search this Thread
Old 04-01-2013, 11:43 PM   #71 (permalink)
Miembro de MCB
 
alkafluence's Avatar
 
Join Date: Jul 2008
Location: The District Outskirts

CCM Fan
AKA Fan
That rollback will lend itself to chopping the next higher ball in the stack, which will have fed slightly into the breech.
alkafluence is offline   Reply With Quote
Old 04-02-2013, 10:59 AM   #72 (permalink)
Wrecking Crewe
 
Mangler's Avatar
 
Join Date: Nov 2012

this marb was boring out at 688 so it was a perfect fit. i think the gun just is a bit rough on soft paint regardless of climate temps. when i run the RPS Premimum (and it usually bores out around 684) i dont break paint at all with it.
Mangler is offline   Reply With Quote
Old 04-05-2013, 04:24 PM   #73 (permalink)
Active Member
 
Join Date: Aug 2006
Location: NW Washington

Ran the DAM indoor last night, gravity fed hopper, Blaze field paint...not a single break all night. Probably 600 rounds over several games.

In addition to the roll back I noticed that the bolt face is pretty narrow and sharp. (I'm assuming the chamfer is for the first strikes) I may take some light sandpaper to that as well, try and break those sharp edges that are contacting the ball. That may have been a factor in all my barrel breaks a couple weekends ago.
Sterling500 is offline   Reply With Quote
Old 04-05-2013, 11:54 PM   #74 (permalink)
Newbie
 
Join Date: Feb 2013

Does anyone know if a Ninja 50ci/4500 tank will fit under the DAM stock without having to adjust/extend it? I'm not very tall, 5'7"-8" and with the stock extended at all, the gun just is a tad too long for me. I have a 68ci already, but dont want to run that and extend it all the way.

I am not into running remote lines, so that is a no go, and I really don't want to go without the stock.
username86 is offline   Reply With Quote
Old 04-14-2013, 12:27 PM   #75 (permalink)
Active Member
 
Join Date: May 2009

Quote:
Originally Posted by username86 View Post
Does anyone know if a Ninja 50ci/4500 tank will fit under the DAM stock without having to adjust/extend it? I'm not very tall, 5'7"-8" and with the stock extended at all, the gun just is a tad too long for me. I have a 68ci already, but dont want to run that and extend it all the way.

I am not into running remote lines, so that is a no go, and I really don't want to go without the stock.
I think it should do, my 48ci fit underneath my stock...
Although the stock had to be pretty much fully extended, so I took the stock off
As it felt what Mike from techpb has described as having a bookcase under your shoulder...

Although I believe the Ultra lite stock solves this problem
__________________
cliffords the man is offline   Reply With Quote
Old 04-14-2013, 01:51 PM   #76 (permalink)
Active Member
 
Join Date: Aug 2006
Location: NW Washington

Ultralight stock?
__________________
FS/FT: Empire Sniper
FS/FT: Q-Loader
Sterling500 is offline   Reply With Quote
Old 04-30-2013, 12:52 PM   #77 (permalink)
z-man
 
Join Date: Apr 2013
Location: Houston, TX

Quote:
Originally Posted by Sterling500 View Post
Ultralight stock?
I just received my ultralight stock and now I can use my Ninja Dura 68/4500. Couldn't even use my 48/3000 with standard stock.
leydenz is offline   Reply With Quote
Old 05-03-2013, 01:09 AM   #78 (permalink)
Newbie
 
Join Date: Feb 2013

Quote:
Originally Posted by leydenz View Post
I just received my ultralight stock and now I can use my Ninja Dura 68/4500. Couldn't even use my 48/3000 with standard stock.
Pictures of the ultralight stock on your gun?

I want to order one as well
username86 is offline   Reply With Quote
Old 05-08-2013, 08:54 PM   #79 (permalink)
z-man
 
Join Date: Apr 2013
Location: Houston, TX

Here's a picture of the stock attached w/o tank. I'll take another w/tank.





By the way, no instructions to replace the stock. It was just the sliding half, not the entire stock as seen in some imaged on Dye's site. Have to remove 2 pins and spring to remove the old and replace new. Use a 1/4 thin wall socket to press spring back down to re-insert pins.
leydenz is offline   Reply With Quote
Old 05-09-2013, 02:14 AM   #80 (permalink)
Newbie
 
Join Date: Feb 2013

Quote:
Originally Posted by leydenz View Post
Here's a picture of the stock attached w/o tank. I'll take another w/tank.

http://farm8.staticflickr.com/7412/8...04fe97ae_m.jpg

http://farm8.staticflickr.com/7408/8...4ae5fde9_m.jpg

By the way, no instructions to replace the stock. It was just the sliding half, not the entire stock as seen in some imaged on Dye's site. Have to remove 2 pins and spring to remove the old and replace new. Use a 1/4 thin wall socket to press spring back down to re-insert pins.

Thank and please do take a picture with a tank attached to it. I want to see if a tank will fit under the ultra light stock without having to extend it too much. Is it as light as they say?
username86 is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » Dye

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 07:43 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC